|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
SECTION 4 SERVICE MODE
Service Mode (Service program) The equipment is provided with a service program built in the microcomputer, like conventional models. Service program operation methods are described in the following.
PLAY MODE Tracking servo and sled servo are turned ON REPEAT/ENTER Tracking gain-up mode while pressing
4. By pressing the ^ key, focus is turned ON from focus searching while entering CLV-S. (draw-in mode) Without disc, focus searching is repeated continuously. 5. By pressing the PLAY MODE key, tracking servo, sled servo and CLV-A (servo in PLAY) are turned ON. 6. When step 4 and 5 are performed, playing begins. No muting is ON in the service mode. 7. By pressing the p key, all servos (focus, tracking and sled) are turned OFF. However, the disc motor revolves for a while by inertia. � Step 3 (Resetting of service mode) 1. Be sure to disconnect the external power supply and remove the solder bridge at the TEST terminals connected before in setting. 2. The set thus becomes available for normal operation.
HOLD c Be sure to turn OFF the HOLD switch (If ON, all the LCD indication and LED are light up)
� MAIN BOARD (Side A) � = (FR) The optical pick-up is moved inwardly + (FF) The optical pick-up is moved outwardly
^ (PLAY/PAUSE) Focus is tuned ON to effect draw-in mode p (STOP)
[All servos are turned OFF]
Descriptions in [ ] indicate major operations in the service mode. For more informatrion, see Step 2.
Fig. 1 Layout of each key
� Step 1 (Service mode setting methods) 1. Turn OFF the HOLD switch with external power supply disconnected. (power is not applied to the set) 2. Solder across the TEST terminals (TAP802). (pin %¢, IC801 (ESPSL/TEST) is grounded) 3. Connect an external power supply. Thus, the set is switched to the service mode. � Step 2 (Operation in the service mode) 1. Once the service mode is effected, the LCD displays 5 indications each of which is repeatedly displayed. However, the following operations can be activated even if LCD indication is effected. 2. By pressing the + or = key, the optical pick-up is movable inwardly or outwardly. However, if this is activated, tracking servo and sled servo are turned OFF, so it can be turned ON by pressing the PLAY MODE key if required. 3. By pressing the REPEAT/ENTER key, the tracking gain-up mode becomes active.
TAP802 (TEST)
Fig. 2 Location of Test terminal
�8�
|
|
|
> |
|
