|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Section
08
Audio Adjustments
Adjusting loudness
Loudness compensates for deficiencies in the low- and high-sound ranges at low volume. 1 Press AUDIO to select Loud. Press AUDIO until Loud appears in the display. 2 Press a to turn loudness on. Loudness level (e.g., Loud MID) appears in the display. 3 Each press of c or d selects level in the following order: LOW (low)MID (mid)HIGH (high) 4 Press b to turn loudness off. Loud OFF appears in the display. Press c or d to select a desired level.
Adjusting subwoofer settings
When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Press AUDIO to select Sub-W2. Press AUDIO until Sub-W2 appears in the display.
# When the subwoofer output is on, you can select Sub-W2.
2 Press c or d to select cut-off frequency. Each press of c or d selects cut-off frequencies in the following order: 5080125 (Hz) Only frequencies lower than those in the selected range are output from the subwoofer. 3 Press a or b to adjust the output level of the subwoofer. Each press of a or b increases or decreases the level of the subwoofer. +6 6 is displayed as the level is increased or decreased.
Using subwoofer output
This unit is equipped with a subwoofer output which can be turned on or off. 1 Press AUDIO to select Sub-W1. Press AUDIO until Sub-W1 appears in the display.
# When the subwoofer controller setting is PREOUT:FULL, you cannot select Sub-W1.
Using non fading output
When the non fading output setting is on, the audio signal does not pass through this units low pass filter (for the subwoofer), but is output through the RCA output. 1 Press AUDIO to select non fading out-
2
Press a to turn subwoofer output on.
# To turn subwoofer output off, press b.
Sub-W1 Normal appears in the display. Subwoofer output is now on. Press c or d to select the phase of sub-
put on/off setting. Press AUDIO until NonFad ON appears in the display.
# When the subwoofer controller setting is only PREOUT:FULL, you can switch to the non fading output on/off setting. (Refer to page 43.)
3
woofer output. Press c to select reverse phase and Rev. appears in the display. Press d to select normal phase and Normal appears in the display.
2
Press a to turn non fading output on.
# To turn non fading output off, press b.
NonFad ON appears in the display. Non fading output is now on.
38
En
|
|
|
> |
|
