PIONEER DJM-707
Owner's Manual

PART NAMES AND FUNCTIONS 5 CH-1 equalizer dials (HI/MID/LOW)
HI Use to adjust CH-1 input treble response (range of adjustment: 13 kHz, +6 dB to �26 dB). MID Use to adjust CH-1 input midrange response (range of adjustment: 1 kHz, +6 dB to �26 dB). LOW Use to adjust CH-1 input bass response (range of adjustment: 70 Hz, +6 dB to �26 dB).

16 CH-2 equalizer dials (HI/MID/LOW)
HI Use to adjust CH-2 input treble response (range of adjustment: 13 kHz, +6 dB to �26 dB). MID Use to adjust CH-2 input midrange response (range of adjustment: 1 kHz, +6 dB to �26 dB). LOW Use to adjust CH-2 input bass response (range of adjustment: 70 Hz, +6 dB to �26 dB).

6 MIC SEND button and indicator
When set to On, the indicator lights, and microphone signals are output at the SEND jacks.

17 Headphone mixing lever (CH-1 � CH-2)
This lever does not function when the monitor SELECT switch (15) is set to [MASTER]. When the monitor SELECT switch (15) is set to [CUE], moving the lever to the left side produces CH-1 monitor output, while moving it to the right produces CH-2 monitor output. Centering the lever at the center detent position produces balanced output of CH-1 and CH-2 signals.

7 Session input level dial (SESSION IN)
Use to adjust the session input volume (range of adjustment: 0 dB to ��).

8 CH-1 SEND button and indicator
When set to On, the indicator lights, and CH-1 signals are output at the SEND jacks.

18 CH-2 SEND button and indicator
When set to On, the indicator lights, and CH-2 signals are output at the SEND jacks.

9 CH-1 EQ ON/OFF switch and indicator
When set to [ON], the indicator lights and CH-1 equalizer is enabled. When set to [OFF], the indicator goes out and the equalizer circuit is bypassed.

19 CH-2 EQ ON/OFF switch and indicator
When set to [ON], the indicator lights and the CH-2 equalizer is enabled. When set to [OFF], the indicator goes out and the equalizer circuit is bypassed.

10 CH-2 input selector switch (PHONO 2/LINE 2 � CD 2)
Use to select input signal from CH-2 PHONO/LINE input jacks or CH-2 CD input jacks, and send them to the TRIM control.

20 POWER indicator
Lights when power is turned On.

21 CH-1 FADER START button
When this button is set to On, fader start and back cue can be performed on the CH-1 CD player. Whether the operation is initiated by operation of the CH-1 fader lever, or by the cross fader lever is determined by the position of the front panel�s FADER START selector switch; the selection is indicated by the lighting of the top panel�s CH-1 FADER START indicator or C.F.1 FADER START indicator. * For DJ CD players supporting the fader start/back cue function, see page 5, �1. Connecting Input Components�.

11 CH-2 TRIM dial
Use to adjust the CH-2 input signal level (range of adjustment: +9 dB to ��).

12 MASTER LEVEL dial
User to adjust the master output volume level (range of adjustment: 0 dB to ��).

13 Booth monitor level dial (BOOTH/SESSION OUT)
Use to adjust the volume level of signals at the BOOTH/ SESSION OUT jacks (range of adjustment: +9 dB to ��). This level can be set independently of the setting of the MASTER LEVEL dial.

22 CH-1 output On/Off lever (TRANSFORM)
Use to set CH-1 output to On or Off (Mute). The lever�s setting angle can be changed in 45° increments (changing of the angle should be performed by an authorized Pioneer service technician).

14 Headphones level dial (PHONES)
Use to adjust the volume level of the headphones output (range of adjustment: 0 dB to ��).

23 CH-1 REVERSE indicator
When lighted, indicates that the front panel�s FADER REVERSE switch has been set so that the CH-1 fader lever operates in the reverse direction (see front panel item 38).

15 Monitor SELECT switch
MASTER side selects MASTER output. (This setting allows output regardless of the setting of the MASTER LEVEL dial.) CUE side selects the channel adjusted with the headphone mixing lever (17).

8
<DRB1353>