|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
;
Quick delivery, the document was usefull, although the copy was i little bit unclear in the details.
1-1. OXF-CP3048/OXF-CP3024
. Setting of the display size and so on. (3) Disconnect the harness from the connector (DIN, 8Pin) on the X terminal board (XP-200). (4) Connect the unique keyboard (TEKTRONIX ACK-200) to the keyboard connector (the lower connector of the two lines of the DIN 8-pin connectors) of the X terminal board (XP-200). (5) Connect the harness to the connector (DIN, 8Pin) which have been disconnected. (6) Input Enter from the keyboard (TEKTRONIX ACK-200) (press the Enter key). Perform the following setting procedures. The setting procedure depends on whether the prompt is displayed or not when inputting Enter. 1) When the prompt BOOT> is displayed Input the following command from the keyboard (TEKTRONIX ACK-200) BOOT> selftest monset 43 (Enter) After the command is input, the display disappears once on the screen, and appears again with the correct screen size. 2) When the prompt BOOT> is not displayed Then input �Enter�. Whenever �Enter� is input, the display setting keeps changing. Press �Enter� until the setting becomes �43� and the correct screen size is displayed. When the correct screen size is displayed, press the F1 key of the keyboard (TEKTRONIX ACK200) to set. (This memorizes the above setting in the internal memory of the X terminal board.) (7) After settings have been finished, disconnect the keyboard (TEKTRONIX ACK-200). (8) Connect the cable which have been disconnected to the connector Ether 0 on the rear panel. Change the /etc/bootptab of the host computer. (9) Checking of BOOT Turn OFF the POWER of the control panel (OXF-CP3048/OXF-CP3024) once, and then turn ON the POWER. After a while, check that the �X� mark is displayed on each LCD display.
OXF-R3 OXF-R3/24
1-15(E)
|
|
|
> |
|
