|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
DMC-J3
CIRCUIT DESCRIPTION
3. TEST MODE
2) To change setting value is available +2 or -2 steps by VOL UP/DOWN key. Disc stops to turn after memorizing the value to E2PROM by PLAY/PAUSE key or not memorizing it to E2PROM by STOP key. Display shows setting value+80h. Remote cont [74 127] changed value [TEST 1] the stop key is pressed [o1] [oo] changed value the stop key is pressed
3. TEST MODE
7) Average data of VC/FE Offset [127F7F] mid 2 figures: VC offset compensation value+80h right 2 figures: FE offset compensation value+80h 8) Average Data of ABCD Offset [13 41] right 2 figures: FE offset compensation value
Unit
3-2 TEST MODE II (AUDIO SPEC)
* Item of audio specification 3-2-1 Procedures 1) Connect #43(TEST0) of IC5 to 2.8V(VDD) and #42(TEST1) of that to GND. Next Connect AC adapter to the unit.(the unit will be in CPLAY mode after TOC reads) Remocon [TEST 4] Unit [o4]
3-1-4 Automatic Adjustment results in Stop Mode After Adjustment * Result will be shown cyclically by SHIT key as follows. Left 2 figures shows display contents number. Example is in remote controller. 1) TOC reading address Remote cont [01FFD0] right 4 figures: header adds/cluster only 2) FOCUS BIAS Value Setting [077272] mid 2 figures: high reflection bias value right 2 figures: low reflection bias value 3) High reflection EF Balance [08 10]
2) The unit will be in CPLAY after TOC reading. Remocon [TOC OK] Unit [o4]
right 2 figures: value
4) Low reflection Pit /Groove of FE Balance [090F0F] mid 2 figures: pit�s FEbalance right 2 figures: groove�s FE balance 5) High reflection Auto Gain Filter of Focus and Tracking [103F40] mid 2 figures: focus gain value right 2 figures: tracking gain value 6) Low reflection Auto Gain Filter of Focus and Track [113538] mid 2 figures: focus gain right 2 figures: tracking gain
3) Choose and playback TNO-02 on the disc by PLAY/PAUSE key Remocon [02] playback TNO Unit [o4]
4) Choose and playback every TNO in the above table by PLAY/PAUSE key. TNO will be chosen TNO 02 if repressing the PLAY/PAUSE key after STOP key pressed, Remocon [05] playback TNO Unit [o4]
10
|
|
|
> |
|
