|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
standby. Note: This is the size adjustment and do not worry about the positioning.
DP-2310/3010 DP-2330/3030
2.8.7.
ADF Original Read Edge & ADF Main Scan Adjustments
1. Place the Original Document on the ADF. 2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper size. Empty or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press the "FUNCTION", "ORIGINAL SIZE (LEDGER/A3)" and "3" keys simultaneously in that order to enter the Service Mode. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy and the Original as Portrait. 6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust the ADF Original Read Edge. 7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Perform the Service Mode F6-90 (ADF Read Main Scan Pos.), to adjust the ADF Main Scan for Side position. 9. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
2.9.
Calibrating the LCD
1. Turn the Main Power Switch on the Back of the machine to the OFF (O) position and leave the Power Switch on the Left Side of the machine in the ON (I) position. 2. Ensure that the F-ROM Card with Firmware Update is not installed in the machine. If the Card is installed in the machine, remove it. 3. Press and hold the "ENERGY SAVER" and "FUNCTION" keys down simultaneously, then turn the Main Power Switch on the Back of the machine to the ON (I) position and continue holding the keys for approximately 30 seconds until the Display becomes stable. The LCD Display starts blinking and shows a "+" on the upper left edge of the display. Note: If you do not hold the "ENERGY SAVER" and "FUNCTION" keys down long enough, the Display may go OFF. 4. Press the "+" on the upper left edge of the display, press the "+" on the lower right edge and press the "+" on the center of the display. Then the display goes to stand-by. Caution: Prevent any damage to the LCD Display by not pressing with Sharp Edged Objects such as a Ball Point Pen, etc. 5. Reboot the machine by cycling the power. Turn the Main Power Switch on the Back of the machine to the OFF (O) then ON (I) position.
53
Ver. 2.0 DEC 2004
|
|
|
> |
|
