|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was very accurate for the part that I was changing, I was able to order the correct part and had no issues with the replacement procedure. However, I was expecting to have more detailed repairs for the lower drive unit.
 ;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
standby. Note: This is the size adjustment and do not worry about the positioning.
DP-2310/3010 DP-2330/3030
2.8.7.
ADF Original Read Edge & ADF Main Scan Adjustments
1. Place the Original Document on the ADF. 2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper size. Empty or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press the "FUNCTION", "ORIGINAL SIZE (LEDGER/A3)" and "3" keys simultaneously in that order to enter the Service Mode. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy and the Original as Portrait. 6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust the ADF Original Read Edge. 7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Perform the Service Mode F6-90 (ADF Read Main Scan Pos.), to adjust the ADF Main Scan for Side position. 9. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
2.9.
Calibrating the LCD
1. Turn the Main Power Switch on the Back of the machine to the OFF (O) position and leave the Power Switch on the Left Side of the machine in the ON (I) position. 2. Ensure that the F-ROM Card with Firmware Update is not installed in the machine. If the Card is installed in the machine, remove it. 3. Press and hold the "ENERGY SAVER" and "FUNCTION" keys down simultaneously, then turn the Main Power Switch on the Back of the machine to the ON (I) position and continue holding the keys for approximately 30 seconds until the Display becomes stable. The LCD Display starts blinking and shows a "+" on the upper left edge of the display. Note: If you do not hold the "ENERGY SAVER" and "FUNCTION" keys down long enough, the Display may go OFF. 4. Press the "+" on the upper left edge of the display, press the "+" on the lower right edge and press the "+" on the center of the display. Then the display goes to stand-by. Caution: Prevent any damage to the LCD Display by not pressing with Sharp Edged Objects such as a Ball Point Pen, etc. 5. Reboot the machine by cycling the power. Turn the Main Power Switch on the Back of the machine to the OFF (O) then ON (I) position.
53
Ver. 2.0 DEC 2004
|
|
|
> |
|
