FUNAI DPVR-6730
Owner's Manual

H9901BD(EN).fm Page 10 Wednesday, February 9, 2005 11:38 PM

To Select a Desired Channel

To Skip a Preset Channel The channels you can no longer receive or seldom watch can be set to be skipped when you access channels by pressing CH. (K/L). � Use the remote control for this procedure. 1) Press VCR, then MENU. 2) Press K or L to select �INITIAL�, then press B. 3) Press K or L to select �CH TUNING�, then press B. 4) Press K or L to select �MANUAL�, then press B. 5) Press K or L to select �POSITION�, then press B. 6) Press the Number buttons, K or L to select relevant position number, then press B. 7) Press K or L to select �SKIP�, then press B to select �ON�. �To memorize the channel again, press B. �ON� will change to �OFF�. 8) Press MENU to exit.
Note: �

You can select a desired channel by using CH. (K/L), or directly pressing the Number buttons on the remote control. � Enter a channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 and 6. If you only press 6, channel 6 will be selected after a brief delay. � You can only select channels 1�99. Manual Channel Preset � Use the remote control for this procedure. 1) Press VCR, then MENU. 2) Press K or L to select �INITIAL�, then press B. 3) Press K or L to select �CH TUNING�, then press B. 4) Press K or L to select �MANUAL�, then press B. 5) Press K or L to select �POSITION�, then press B. �When a weak signal is received in Manual Tuning mode, you can change the background to solid blue or the static screen by pressing C.RESET. 6) Press the Number buttons, K or L to select your desired position number, then press B. �You can select position number 01-99. �If �ON� appears on the right side of �SKIP�, press K or L to point to �SKIP�. Then, press B to select �OFF�. �If you want to remove scrambled signals, press K or L repeatedly to point to �DECODER�. Then, press B to select �ON�. 7) Press K or L to select �CHANNEL�, then press B. 8) Press K or L to start scanning. �The unit�s tuner will begin to search up or down automatically. When a channel is found, the unit will stop searching and the picture will appear on the TV Screen. �You can select desired channel number by using the Number buttons. You must refer to the following Channel Plan table and press three digits to select the channel number. (To select channel 24, press �0� button first and then press �2� and �4�.) �If this is the channel you want, press B.
Channel Plan
CH Indication TV Channel

To confirm that a channel has been deleted, press CH. (K/L).
MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK

MANUAL POSITION CHANNEL DECODER SKIP P08 008 [OFF] [ON]

CH TUNING AUTO MANUAL MOVE

Channel Reprogramming You can replace two channels. � Use the remote control for this procedure. 1) Press VCR, then MENU. 2) Press K or L to select �INITIAL�, then press B. 3) Press K or L to select �CH TUNING�, then press B. 4) Press K or L repeatedly to select �MOVE�, then press B. 5) Press K or L repeatedly to select the position number you want to change the channel, then press B. �You cannot select a position number where �- - -� appears next to the number. This is because SKIP is set to �ON� for this position number. �When a weak signal is received in Channel Reprogramming mode, you can change the background to solid blue by pressing C.RESET. If you press the button again, the background will return to the static screen. 6) Press K or L repeatedly until the channel move to another position number, then press B.

01 � 10 21 � 69 74 � 78 80 � 99, 100 121 � 141

IRA � IRJ, GAP E21 � E69 X, Y, Z, Z+1, Z+2 S1 � S20, GAP S21 � S41

�This unit can receive Hyper and Oscar frequency bands. 9) Press MENU to exit. Note: � To confirm that a channel has been added, press CH. (K/L).
MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK

MANUAL POSITION CHANNEL DECODER SKIP P08 008 [OFF] [OFF]

CH TUNING AUTO MANUAL MOVE

10

EN