|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I searched EVERYWHERE looking for the manual/s on this "extinct" amp. Owner-Manuals.com made it available and for nearly nothing. Thanx to them, I can decipher the unknown cables and sort them out. Thanx, Owner-Manuals.com!!
;
Yes thank you i got the file i was after. There was a slight problem in my communication but it all worked out well.
A job well done.
 ;
Great manual...really saved me. The only problem is that I thought I would be able to download it directly when I paid for it but never received the download instructions until the next morning. The board trace pages were somewhat light also: really need to turn up the contrast on the printer before printing them. The schematic page was great; very clear! Well worth the money.
;
I've been in the electronic business for a long time. I used to buy Sam's Photofact for my needs which intailed having to go to the store and paying about $20 for a package of 3 different units so I was forced to buy more than I needed just to get one.
Owner manual is just at your keyboard and the information is almost instantansouly and the cost is very reasonable. Easy to print out if needed or simply read off of the screen. The larger the screen the better for obvious reasons.
;
Very good manual, at a very good price. Received in a timely manner
Service manual CP 385 / CP785
5-6 Sound amplification The TDA8944J (TDA8946J) is a stereo BTL audio amplifier capable of delivering 2 x 7 W (2 x 15 W) output power to an 8 � load at THD = 10%, using a 12 V power supply and an external heatsink. The voltage gain is fixed at 32dB. With the three-level MODE input the device can be switched from �standby� to �mute� and to �operating� mode. The TDA 8944J outputs are protected by an internal thermal shutdown protection mechanism and short-circuit protection. Power amplifier The power amplifier is a Bridge Tied Load (BTL) amplifier with an all-NPN output stage, capable of delivering a peak output current of 1.5 A. The BTL principle offers the following advantages : - Lower peak value of the supply current. - The ripple frequency on the supply voltage is twice the signal frequency. - No DC-blocking capacitor - Good low frequency performance Mode selection The TDA894xJ has several functional modes, which can be selected by applying the proper DC voltage to pin MODE. Mute : In this mode the amplifier is DC biased but not operational (no audio output). This allows the input coupling capacitors to be charged to avoid pop-noise. The devices is in mute mode when 2.5 V < VMODE < (Vcc-1.5 V). Operating : In this mode the amplifier is operating normally. The operating mode is activated at VMODE < 0.5 V. 5-7 Vertical deflection The vertical driver circuit is a bridge configuration. The deflection coil is connected between the output amplifiers, which are driven in phase opposition. The differential input circuit is voltage driven. The input circuit is especially intended for direct connection to driver circuits which deliver symmetrical current signals, but is also suitable for asymmetrical currents. The output current of these devices is converted to voltages at the input pins via resistors R350 and R351. The differential input voltage is compared with the output current through the deflection coils measured as voltage across R302, which provides internal feedback information. The voltage across R302 is proportional to the output current. Flyback voltage The flyback voltage is determined by an additional supply voltage Vflb. The principle of operation with two supply voltages (class G) makes it possible to fix the supply voltage Vp optimum for the scan voltage and the second supply voltage Vflb optimum for the flyback voltage. Using this method, very high efficiency is achieved. The supply voltage Vflb is almost totally available as flyback voltage across the coil, this being possible due to the absence of a coupling capacitor. Protection The output circuit has protection circuits for : - Too high die temperature - overvoltage of output stage A Guard circuit The guard signal is not used by the TDA936x to blank the screen in case of fault condition. Damping resistor
- 43 -
|
|
|
> |
|
