|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Perfect. Very good service and very good scanning quality. All sheets are very legible. Thank's
;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
;
Very comprehensive document which is a must-have for any Satellit 2100 owner whose set up is somewhat intricate. Due to the bad quality of the pictures that are rather dark and a bit blurred I gave 4-star feedback.
;
The manual was missing 2 pages but when I presented the problem to the company they made every attempt to get the 2 pages to me, when they couldn't they refunded my money. A very pleasing and easy transaction. The manual they provided was the original, it was concise and to the point. I plan to do business with this company again when should the need arise.
Remote controller
Using the remote controller
On Scan
Master Volume
Number buttons
RCVR/Tape
Standby/On
1 ABC
2 DEF
3 GHI
4 JKL
5 MNO
6 PQR
7 STU
8 VWX
9 YZ-
Standby
Direct Tuning 0/10 / Scan
Speakers
A B
Clear
Enter
Zone 2 Off Display Direct Tuning Memory FM Mode Character
Phones
DVD
Video
Tape 2 Monitor
Tape 1
FM
AM
Phono
CD
Bass
Treble
Balance
L
R
DTM-5.3
Standby/On
Memory
Setting the ID number
Programming the remote controller ID (This procedure is not required if you are using only one DTM-5.3.) If you are using multiple DTM-5.3 units, all units will respond to an operation on one of the remote controllers. To avoid this, you can establish up to nine ID numbers for the remote controllers. The same ID number should be set on both the remote controller and the corresponding DTM-5.3. You can use the remote controller as long as its ID matches that speci�ed on the main unit. To cancel the ID number, set the number to �0.� If the ID on the main unit is set to �0,� all remote controllers (with ID 0-9) can control the unit.
3 Turn on the power to the DTM-5.3, and press and hold down the Memory button.
The current ID number of the main unit appears on the display for �ve seconds.
DTM-5.3 (this unit)
Standby/On
Memory
Current ID
4 While the current ID of the unit appears on the display, press the On button on the remote controller.
Programming the ID number
1 On the remote controller, while pressing and holding down the RCVR/Tape button, press the Enter button, then release both buttons.
Remote controller
The remote controller will send its ID information to the unit, and the ID of the unit will be changed to match the remote controller�s ID.
Remote controller
2 Press one of the number buttons (1�9, 0).
For example, if you press �3� in Step 2: �UNIT ID 0� � �UNIT ID 3� The unit�s ID will change to �3.�
The number you pressed is set as the ID.
Remote controller
Hint:
You can use the number buttons on the main unit instead of pressing the On button on the remote controller. In this case, press the same number as the remote controller�s ID (selected in Step 2). E.g., Press �3.�
Checking the remote controller�s ID:
Press the Scan button on the remote controller while the display indication shown in Step 4 appears. The remote controller�s ID appears on the display. E.g., REMOTE ID 3
Note:
The unit will not respond to remote controller operations if the ID numbers do not match.
28
|
|
|
> |
|
