|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
;
The manual was very helpfull, it answerdes all my questions, and i was surprized to find the original manual on this site! Big thumbs uP:)
Selecting an input source
� Using the on-screen display
1. Press the OSD MENU button. 2. Select �Input Selector� and then press the right edge of the ENTER/Cursor button. 3. Select �Digital Input Setup� and then press the right edge of the ENTER/Cursor button. The �Digital Input Setup� screen appears. To display VIDEO 2 and later items, press the lower edge of the ENTER/Cursor button. � Select the digital input connector from among �OPTICAL 1,� �OPTICAL 2,� �COAXIAL 1,� �COAXIAL 2,� and �� � � �.� � If no digital input connector is assigned to the selected input source, it will be indicated as �� � � �.� � To enter the setting, move the cursor vertically using the ENTER/Cursor button. 4. To set the input signal format, move the cursor to the line immediately below the input source and then press the right or left edge of the ENTER/Cursor button. � Select the digital audio format from among �Automatic,� �Digital,� �Analog,� �PCM,� and �DTS.� � Holding down the right or left edge of the ENTER/Cursor button sequentially changes the setting. 5. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode. Notes on DTS 1. If you play a CD or LD that supports DTS when the �Analog� or �PCM� setting is selected on the DTR-7/DTR-6, the DTS encoded signal will not be decoded and noise will be output. This noise could damage the amplifier and speakers. Therefore, be sure to select �Automatic�, �Digital� or �DTS� and use the digital input jacks (OPTICAL1/2 /COAXIAL1/2) to connect the DTS source. 2. If you play a CD or LD that supports DTS when the �Automatic�, or �Digital� setting is selected, you may hear a noise for a short while until the DTS decoder recognizes the DTS encoded signal and starts operating. This is not a malfunction. 3. If you press the PAUSE or SKIP button on the player while playing a DTS source, a short noise may be heard. This is not a malfunction. In such cases, try playing the source in the �DTS� mode. 4. The DTS indicator on the DTR-7/DTR-6 lights up while it plays the DTS source. When playback concludes and the DTS signal transmission stops, the DTR-7/DTR-6 remains in DTS mode and the DTS indicator remains lit. This prevents noise when you operate the PAUSE or SKIP button on the player. Therefore, if the source switches from the DTS signal to the PCM signal immediately, the PCM signal may not be played. In this case, stop the playback of the source on the player for about three seconds, then resume playback. 5. Some CD players and LD players may be unable to play DTS sources correctly even if you connect the player to the DTR-7/ DTR-6 digitally. This is because the digital signal has been processed (such as the output level, sampling frequency, frequency response, etc.), and the DTR-7/DTR-6 cannot recognize the signal as DTS data. Therefore, you may hear noise when you play a DTS source while processing the signal. 6. The OUT jacks of the VIDEO-1, VIDEO-2, and TAPE connectors output analog audio signals. Do not record CDs or LDs that support DTS using these jacks. Otherwise, you will record a DTS-encoded signal as noise.
* Digital Input Setup * CD DVD VIDEO 1 :COAXIAL 1 Automatic :COAXIAL 2 Automatic :---Automatic
29
|
|
|
> |
|
