|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
 ;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
;
Great copy of the manual, has all information required for servicing,
DV-626D
FL
39 41
Descripor n of Err tio
Smeouonverge ti GC c t Spindle timeout
Causes if with a DVD
SGC could not converge during detects the peak
Causes if with a CD
Operation of the Unit
Open Stop
The unit did not enter Stop mode within 10 seconds of issuance of a Stop command. The spindle could not converge into within ± 12% of the target FG rotation speed within 10 seconds after spindle kick. The first time after startup (the first time after disc distinction), it doesn't become the number of the target rotation within five seconds. The first time after startup, detects the abnormal rotation number of high-speed continuously 3 loops. DVD: 5 to 9 mS , CD: 40 to 60 mS rAtfaeirothe ishicofivetisees ndts.r startup, it doesn't become the number of the target o t t n w t e n nd m co af e Detects the abnormal high-speed or low-speed rotations. DVD: 5 to 9 mS , CD: 40 to 60 mS
48
Sansitlie n Gmeout tr pind o F ti
Stops. (FG timeout)
49
Spindle PLL transition timeout
Stops. ("t73t"ns dirocess.) during s ar i i g p splayed Stops. ("73" is displayed during starting process.) Stop
4A 51
Spindle lock timeout Spindle could not lock more than 1.5 seconds before start the AFB. Auto sequence timeout of peak detection Au o ut of f nce timteosequeocus jump down Au o ut of f nce timteosequeocus jump up A DTS T di e no dettu i n i cin 1 seco waa t e . DBUCY (pd ak t reecrtnow)thommand nd s fserntthe ABUSY did not return within 30 mS after the FJMPD (Focus jump 1 to 0) command was sent. ABUSY did not return within 30 mS after the FJMPU (Focus jump 0 to 1) command was sent.
52
Stop
53 54 55
Stop Stop Stop
Au o ut of pl ce A SUMON ( n ay re GC wit a n rin m c m e he timteosequenay AGC GBUSY did plot -Aturn-mehisu50g) Soaftmratnd was sent. Au o ut of di ce timteosequensc-type- ABUSY did not return within 2 seconds after the sensing DJSRT (disc-sensing) command was sent. Auto sequence timeout of ATB2 Au o ut of t nce timteosequeracking servo ON Au o ut of AT e timteosequencB1 Auto sequence timeout of focus gain adjustment Au o ut of t nce timteosequeracking gain adjustment Auto sequence timeout of offset adjustment Auto sequence timeout of modulation factor measurement Auto sequence timeout of auto focus bias Auto sequence already busy Pause retry error ABUSY i Inter al u T a t i r h s comd a er of TBLOFSd(d notnretArnBwitfhen t1 e econpletfiton theexternal ATB) command was sent. ABUSY did not return within 500 mS after the TSON (tracking servo ON) command was sent. AB ter Y id B) return n it wa 2 se m (exUSnaldATnot commawdhin s 00 nt.S after the TBL ABUSY did not return within 2 seconds after the FGN (focus gain adjustment) command was sent. ABUSY did not return within 2 seconds after TGN (tracking gain adjustment) command was sent. ABUSY did not return within 1 second after the CMDAVE (offset adjustment) command was sent. ABUSY did not return within 200 mS after the ADJMIR (modulation factor measurement) command was sent. AB to o dis n a ) t om wi hi 2 s con . (auUSfYcud biotsrecurnmatndnwasesentds after the AFB A command could not be sent because ABUSY was low. ABUSY did not return within 200 mS after TLV command was sent. P t usit mode cou e ea be afaer e had been lrd lnotsed.restored within three retries
56
Stop
57 58
Stop Stop
59 5A
Stop Stop
5B
Stop
5C
Stop
5D
Stop
5F 62
Stop Continues operation
65
|
|
|
> |
|
