|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly what was needed to assess the product - excellent value and great service
 ;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
DV-660S DV-660H
6. DISASSEMBLY AND REPLACEMENT OF MAIN PARTS
6-1. DISASSEMBLY
1. Remove five screws (A), and remove the cabinet. Note: When assembling it, tighten the screws in order of 1 - 2 . (Because the set may rise a little by tightening the screws.)
(A) x2 1 Top Cabinet (A) 2
(A) x2 1
2. Remove two screws (B). 3. Remove one screw (C). 4. Release the hooks of the front panel at two places on both sides and at three places on the bottom, and slide the front panel toward
(B) x2 (F) x4 (D)
you. 5. Disconnect the connectors (D) and (E). 6. Remove four screws (F) which installs the mechanical unit.
(E)
Hook Front panel (C) Hook
(H) (J) Main PWB (G) (L) (S) (L) (M) x7
7. Disconnect the lead lines (G) and (H) and (J) from the main PWB under the mechanism. 8. Remove two screws (K) on both sides of the terminal angle frame. 9. Remove three screws (L) which install the terminal PWB. Mechanism 10. Remove seven screws (M) and one screw (N) which install the
(S)
terminal block. 11. Remove three screws (P) of the display PWB. 12. Remove two screws (Q) of the decorative leg. (P) x3 13. Push out the middle pin (R) of the setting leg in the direction opposite to insertion. (Two places) 14. Remove two screws (S) which install the main PWB under the mechanical unit.
(N) (K) x2 21-Pin Euro-SCART PWB (L) (R) x2 Terminal PWB
Display PWB
(Q) x2
(W)
15. Remove three screws (T) which install the volume PWB of the front panel. 16. Remove three screws (U) which install the operate PWB. * The spacer and insulation seat under the indication tube of (V) and (W) are bonded with both-side sticking tape. 17. Remove one washe (X) and one nut (Y) which install the shuttle knob.
(V)
Volume PWB
(T) x3
(U) x3
(Y)
Operate PWB (X) Shuttle knob
6-1
|
|
|
> |
|
