|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
4-1. SCHEMATIC DIAGRAMS
4-1. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) � All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. � Chip resistors are 1/10 W unless otherwise noted. k�=1000 �, M�=1000 k�. � Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. � Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520
L Camera
1. Connection
Pattern box
Color bar chart Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = About 30 cm (PTB-450) L = About 13 cm (PTB-1450) Pattern box Front of the lens
Kinds of capacitor External dimensions (mm) Case size � Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. � Parts with � differ according to the model/destination. Refer to the mount table for each function. � All variable and adjustable resistors have characteristic curve B, unless otherwise noted. � Signal name XEDIT � EDIT PB/XREC � PB/REC � 2: non flammable resistor � 5: fusible resistor � C: panel designation � A: B+ Line � B: B� Line � J : IN/OUT direction of (+,�) B LINE. � C: adjustment for repair. � A: not use circuit � Circled numbers refer to waveforms. (Measuring conditions voltage and waveform) � Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M� input impedance is used) � Voltage values change depending upon input impedance of VOM used.) Precautions for Replacement of Imager � If the imager has been replaced, carry out all the adjustments for the camera section. � As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light.
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
H
Yellow Cyan Green White Magenta
AB A=B BA Fig. a (Video output terminal output waveform)
Red Blue
Electronic beam scanning frame CRT picture frame Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
DCR-DVD105/DVD105E/DVD605/DVD605E_L3 4-1
|
|
|
> |
|
