|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
Diagnostic Software, Trouble Shooting and Test Instructions 5.5
5.5.1
DVD 723-743
5.
EN 27
Basic Engine
Version Number In the basic engine tests, the version number of the Basic Engine will be shown first, as the following example: Figure 5-25 By pressing OPEN/CLOSE the user confirms that the disc motor is running. Pressing STOP indicates the disc motor does not work. Pressing PLAY proceeds to the next test, after a reset of the disc motor (nucleus BeDiscMotorOff). If the user presses PLAY before pressing OPEN/CLOSE or STOP, the result of this test will be TRUE (disc motor is running). 5.5.5 Focus Test (Visual Test) The fourth Basic Engine test tests the focussing. First focussing is turned on by calling nucleus BeFocusOn. The display will look as follows:
CL 16532162_043.eps 080102
CL 16532162_040.eps 080102
Figure 5-22 By pressing the PLAY key, the Basic Engine tests are started. 5.5.2 Tray Test First, the tray is tested. The purpose of this test is also to give the user the opportunity to put a disc in the tray of the DVD player. Some tests on the Basic Engine require that a disc (e.g. DVD MPTD test disc) is present in the player. At the end of the Basic Engine tests this tray test will be repeated solely to enable the user to remove the disc in the tray. The local display will look as follows:
CL 16532162_044.eps 080102
Figure 5-26 By pressing OPEN/CLOSE the user confirms that the focussing was succesful. Pressing STOP indicates a focussing failure. Pressing PLAY proceeds to the next test after a reset of the focussing (nucleus BeFocusOff). If PLAY is pressed before OPEN/CLOSE or STOP, the result of this test will be TRUE (focus successful). 5.5.6 Radial Test (Visual & Listening Test) The fifth Basic Engine test tests the radial functionality (nucleus BeRadialOn). The local display looks as follows:
CL 16532162_041.eps 080102
Figure 5-23 By pressing OPEN/CLOSE the user can toggle the position of the tray. Note that this test will not contribute to the test result of the Basic Engine. Pressing PLAY will proceed to the next test. At this point, the tray will be closed automatically by the software if it was open. 5.5.3 Sledge Test (Visual Test) The second Basic Engine test tests the sledge. The user can move the sledge as many times as desired by using OPEN/ CLOSE (nucleus BeSledgeOut) and STOP (nucleus BeSledgeIn). Pressing PLAY on the local keyboard proceeds to the next test. Note that this test will not contribute to the test result of the Basic Engine. The local display will look as follows during the sledge test:
CL 16532162_045.eps 080102
Figure 5-27 By pressing OPEN/CLOSE the user confirms that the radial function works.Pressing STOP indicates the function does not work. Pressing PLAY proceeds to the next test, after a reset of the radial (nucleus BeRadialOff). If the user presses PLAY before pressing OPEN/CLOSE or STOP, the result of this test will be TRUE (radial successful). 5.5.7 Jump Test (Listening Test) The sixth and last Basic Engine test tests the jumping by calling nuclei BeGroovesIn, BeGroovesMid and BeGroovesOut. During this test, the local display looks as follows:
CL 165321625_042.eps 080102
Figure 5-24 5.5.4 Disc Motor Test (Visual Test) The third Basic Engine test tests the disc motor (nucleus BeDiscMotorOn). The local display looks as follows:
|
|
|
> |
|
