|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
;
Exactly what was needed to assess the product - excellent value and great service
;
A site where discontinualed schematic diagrams and back dated information can be found on discontinued radios tv's and any electronic equipment can be found. Newer manuals either Service and operating manuals. Radio amateurs should find this site a great source for ham radio equipment manuals. I will return to this site should I need information on any electrical equipment. priced easy to download in a PDF format and print pages need to undertake the repair.
;
Quality scan of the original. All the detail necessary to troubleshoot, repair and adjust the unit. I'm sure I will be downloading more manuals in the future as the need arises.
EN 152
9.
DVDR880-890 /0X1
Circuit-, IC Descriptions and List of Abbreviations
tion, an additional circuit for suppressing the audio carrier of the adjacent channel is used. This circuitry is adjusted by coil [5710] for maximum suppression at 40.4MHz. IF demodulator The signal from the tuner and IF-selection circuit is processed by the demodulator IC TDA 9818/9817 [7710]. The signal �PSS� to pin 3 switches between demodulation of positive (SECAM only) or negative modulated video carriers. A QSSaudio-IF signal SIF1 is generated for demodulation in the sound processor [7600]. The audio-IF carrier is selected in the audio SAW filter [1702]. This filter is switched for SECAM L�. If the signal �SB1� is �high�, the switch [7714] is closed and the diode [6705] is not conducting. For all other standards the diode [6705] is conducting and the switch [7714] is open. The output signal of this SAW filter is firstly processed in the TDA 9818. Audio carriers are converted from the tuner IF level to the audio IF position and further processed in the audio demodulator [7600]. The AFC coil [5711] on the TDA 9818/ 9817 is adjusted so that when a frequency of 38.90 MHz is supplied to the IF output of the tuner, the AFC voltage on pin 17 of [7710] is 2.5V. The setting of the picture carrier frequency for SECAM L in the TDA 9818 is achieved by connecting pin 7 of the IC via a resistor [3710] to ground. The switch [7701] and the signal �SB1" do this. The HF-AGC is set using the potentiometer [3724] so that, with a sufficiently large antenna input signal (74 dBµV), the voltage at the IF output of the tuner [1705] pin 11 is 500 mVpp. This setting must be carried out when the audio carrier is switched off. The demodulated video signal appears on pin 16 of [7710]. The AGC voltage at pin 4 is used to determine the antenna signal strength after a buffer [7717] with the signal �AGC� and an analog input port of the CC-µP. The trap [1704] reduces the sound carrier remainders in the video for BG standards. The trap [1706] works in the same way for the Pal-I standard only. For all other standards the switch [7713] is closed via [7706] and �SFS_TS�-line set �high" to bypass this trap. In these cases the selectivity of the SAW filter [1701] is sufficient. The coil [5713] for non-BG standards realizes a frequency response correction. This correction is not desired for SECAM L' and therefore short-circuited by [7716] (signal SB1 is �high� and [7702] has on-status). The demodulated video signal �VFV� is available after the buffer and limiting stage for noise peaks [7711]. The FM-PLL demodulator function of TDA 9818 is not necessary and therefore deactivated by the resistor [3739]. Audio demodulator The sound demodulation is done by the MSP3415 [7600], which is also fully controlled via I²C-bus by the CC-µP (determination of bandwidth, amplitude, standard, �).The audio signals are available at pin 30 and pin 31 of [7600] and fed as �AFER�- & �AFEL�-line to the audio-I/O for further processing.
|
|
|
> |
|
