|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
As Always you can find here manuals even of difficult TV scheme which are scan in almost perfect way.clear and fast!!!!!
Great work thanks!
;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
B. Signal flow of the PAL colour in the record mode
Video input
(5.06±4.43) MHz
2
Video AGC
BPF
4.43MHz
ACC AMP
4.43MHz
MAIN CONV
IMHz LPF
O
5.06MHz 627KHz
To. PREAMP 2Head: Pin & of LA7411 4Head: Pin ) of LA7416
u
Killer
I
BLOCK 2. PAL COLOUR SIGNAL FLOW A recording composite video signal is fed to the AGC circuit from Pin 12 of IC301, and its output signal is passed through a BPF (Band Pass Filter) to eliminate the luminance components, and then only the colour signal is fed to the ACC (Auto Colour Controller) amplifier. The gain of the ACC amplifier is controlled by the DC voltage at Pin 41 of IC301. The signal from ACC AMP is fed to the Main Converter to transfer 4.43MHz to 627KHz. That is, the summation and substraction of the two input signal frequencies are obtained from this Main Converter. Here, the two input signal frequencies are 4.43MHz and 5.06MHz. The output frequencies from the Main Converter are approximately 627KHz and 9.49MHz. The output from the Main Converter is fed to the killer circuit through the LPF. The LPF is used to eliminate unwanted frequencies (ie: 9.49MHz). The Killer detector gives a reliable operation thanks to the application of both systems i.e. synchronized detection (APC Killer) and the Peak detection (ACC Killer) in the record mode. The signal is obtained from Pin 38 of IC301 as the recording colour signal. The output signal from Pin 38 of IC301 is fed to the PREAMP IC (2 Head: Pin 7 of LA7411, 4 Head: Pin 10 of LA7416). C. Signal flow of the luminance in the playback mode The playback Y-FM from the PREAMP (approximately 60dB amplification) is fed to the PB EQ circuit to perform frequencylimiting and phase compensation. The output signal from the PB EQ circuit is input to Pin 1 of IC301 and then this signal is passed through the FM-AGC so that the signal level is kept constant. The output signal is fed to a Double Limiter. The Double Limiter's function is as follows: As the high frequency components of the playback Y-FM signal are deteriorated due to the characteristics of the TapeHead system, Y-FM signal (black spike) effect may be seen in the playback picture, and the Double Limiter is used to compensate for this. The signal from the Double Limiter is fed to an FM Demodulator. This demodulated video signal is passed through the LPF and the emphasized high frequency component from the Main Emphasis is de-emphasized. The signal from the Main DEemphasis is fed to pin 4 of IC301.
15
|
|
|
> |
|
