|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
Section
Audio Adjustments
11
# If the subwoofer setting has been previously adjusted, the frequency of that previously selected will be displayed instead of 80.
2 Press m or n to select cut-off frequency. Each press of m or n selects cut-off frequencies in the following order: 5080125 (Hz) Only frequencies lower than those in the selected range are output from the subwoofer. 3 Press r or q to adjust the output level of the subwoofer. Each press of r or q increases or decreases the level of the subwoofer. +6 6 is displayed as the level is increased or decreased.
1 Press A to select non fading output setting. Press A until NOFAD: 0 appears in the display. 2 Press r or q to adjust the output level of the non fading. Each press of r or q increases or decreases the level of the non fading. +6 6 is displayed as the level is increased or decreased.
Using the high pass filter
When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn the HPF (high pass filter) on. Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press A to select HPF. Press A until HPF appears in the display. 2 Press r to turn high pass filter on. HPF : 80 appears in the display. High pass filter is now on.
# If the high pass filter has been previously adjusted, the frequency of that previously selected will be displayed instead of HPF : 80. # To turn high pass filter off, press q.
Using non fading output
When the non fading output setting is on, the audio signal does not pass through this units low pass filter (for the subwoofer), but is output through the RCA output. 1 Press A to select non fading output on/ off setting. Press A until NOFAD:ON appears in the display.
# When the subwoofer controller setting is only P/O :FUL, you can switch to the non fading output on/off setting. (Refer to page 72.)
Audio Adjustments
2 Press r to turn non fading output on. NOFAD:ON appears in the display. Non fading output is now on.
# To turn non fading output off, press q.
Adjusting non fading output level
When the non fading output is on, you can adjust the level of non fading output.
3 Press m or n to select cut-off frequency. Each press of m or n selects cut-off frequencies in the following order: 5080125 (Hz) Only frequencies higher than those in the selected range are output from the front or rear speakers.
En
55
|
|
|
> |
|
