|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent, fast delivery, excellent product. Good luck!
;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
DV-HR300S/HR350S DV-HR300H DV-HR300X
5-3. Notes for servicing
1. After replacing the HDD or main PWB, register the HDD-ID again. 2. After replacing I54R NOR flash (IC7502) or NAND flash (IC7509), upgrade the version using the CD. All the data in the HDD will be formatted by replacing the main PWB unit. The following parts cannot be replaced as the system information needs to be written. (Replace the PWB.) 1. EEPROM for I54R, IC7507 and IC7508 Setting procedure after replacement of HDD or main PWB 1) HDD installation The unit can be started after installing the HDD, but key operation is impossible since the HDD-ID is not registered. Perform HDD aging to register the HDD-ID. 2) HDD aging The test mode can be accessed after replacing the HDD. [1] Enter the test mode with the keys on the main unit (press the channel UP key and recording stop key simultaneously). [2] Enter �4� to open the drive screen. [3] Press the play key to enter the HDD aging mode. �0� appears on the LCD of the front panel. It increases to 58 and then changes to �777� when the aging is completed. Should �EEE� appear, replace the HDD and start the process over. Aging takes approx. 2.5 hours. [4] The aging is completed when �777� appears, and the HDD-ID is registered automatically. If the main PWB unit is replaced, enter the test mode and press the �10/0� key on the remote control to register the HDD-ID. [5] Restart the unit and check the operation. 3) Factory setting Initialize all the settings. Enter the test mode and press the �11� key on the remote control. The display stays black during the initialization process. Initialization is completed when the test mode appears on the LCD display following �507�.
5-4. Writing of software
1. Press the power key to turn on the power. 2. Open the tray with the tray open/close key and place the version upgrade CD. 3. Close the tray. Upgrade begins automatically. �200� appears on the main unit display. 4. When the upgrade finishes, the tray opens and �208� appears on the main unit display. 5. Turn off the power to complete the upgrade. � Upgrade the writer in the same way. In this case, �300� and �307� appear on the main unit display during the process.
12
|
|
|
> |
|
