|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent printing quality. A complete and very useful manual with all details.
 ;
This is a great site. I placed my order and by the next am it was available for download. Had some problems with some missing copy on some pages. Once I brought the error to the OMC's attention, the issue was resolved. I'll come back again.
;
Mi spiace per non poter scrivere in inglese... ma sono veramente soddisfatto del servizio offerto. Grazie..!!
;
The quality of this manual is good. It has all schematics and setup information for both the MDS-B3 and the MDS-B4. The scan quality is quite good, all pages are readable, This service manual also contains scans of the operating instructions from the User manual.
;
Quick site processing. A complete and very useful manual with all details. Thank you!
0 1 2 3 4 5 6 7
Reset SLED TILT LD SP Focus TRK Sled CLVA FCS. Srch
� Sled FWD � Sled REV
Reset the Sled and Tilt to initial position. Turn ON/OFF the laser. Turn ON/OFF the spindle. Search the focus and turn on the focus. Turn ON/OFF the tracking servo. Turn ON/OFF the sled servo. Turn ON/OFF normal servo of spindle servo. Apply same voltage as that of focus search to the focus drive to check the focus drive system. Move the sled outward. Perform this operation with the tracking servo turned off. Move the sled inward. Perform this operation with the tracking servo turned off.
6-6. EVR Adjustment
The picture display adjustment of both NTSC and PAL can be performed by the MANUAL adjustment using the menu display of the test mode. Press 3 appears. of the remote controller. The following check menu
### # 1. NTSC 2. PAL 3. NTSC 4. 5. 6. 7. PAL Copy Copy PUMP
EVR
###
Main Menu # Adjustment Adjustment Default Set Default Set NTSC � PAL PAL � NTSC
The following menus are normally not used.
8. Change to NTSC 9. Change to PAL Exit : RETURN
3. Track/Layer Jump 4. Manual/Adjustment 5. Auto Adjustment
The persons who do not know well about these menus should not use them.
1 NTSC Adjustment
The respective EVR adjustment channels of the NTSC screen can be set by the MANUAL adjustment. Press 1 of the remote controller. The following sub-menu appears. ### EVR ### # NTSC Adjustment # RGB AMP 1 ch BRIGHT 2 ch GAMMA0 10 ch GAMMA1 11 ch CONTRAST 3 ch COM AMP 4 ch SUB_B 8 ch SUB_R 9 ch (Next) Exit : RETURN
6. Memory Check
EEPROM DATA Focus Gain TRK. Gain Focus Offset TRK. Offset L.F. Offset Analog FRSW PLL DAC Gain EQ Boost Jitter Mirror Time � �DL� � CD SACD SL L0 L1 xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx CLEAR : Default Set 0. 1. 2. 3. 4. 5. 6. 7. 8.
1 -1. Setting the respective channels
Press the desired key ( 0 for an example) of the remote controller from the sub-menu display. A binary number appears to the right of the selected channel on the sub-menu as shown. ### EVR ### # NTSC Adjustment # RGB AMP 1 ch _60 BRIGHT 2 ch � GAMMA0 10 ch Flashes GAMMA1 11 ch CONTRAST 3 ch COM AMP 4 ch SUB_B 8 ch SUB_R 9 ch (Next) Exit : RETURN
This screen displays current servo adjusted data stored in the EEPROM. Though adjusted data can be initialized with the CLEAR key, they cannot be restored after initialization. So, before clearing, make a note of the adjusted data. For reference, the drive has been designed so that the gain center value is 20 and offset value is 80 except the Mirror Time. Other values will be in a range of 10 to 80. If extreme value such as 00 or FF is set, adjustment will be faulty. In such a case, check for disc scratch or cable disconnection, then perform adjustment again.
0. 1. 2. 3. 4. 5. 6. 7. 8.
6-9
 $4.99 DVP-F5 SONY
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
