|
Who's Online
There currently are 5987 guests and 2 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
DVD SETUP Audio Setting
Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs of the DVD player.
Display Setting
You can change certain aspects of the DVD�s display screens, on-screen messages and the display panel on the front of the DVD player. 1 Press SETUP during playback is stopped. 2 Press K or L to select DISPLAY, then press
NOTE:
� These audio settings are effective only when using a digital connection. Although you may change the settings from the on-screen display, these audio settings do not actually affect the sound when using an analogue connection. 1 Press SETUP during playback is stopped. 2 Press K or L to select AUDIO, then press ENTER. 3 Press K or L to choose the below items and press
ENTER.
3 Press K or L to select the below items, then press
ENTER. TV Aspect: � Press K or L for an item selection, then press
ENTER repeatedly to turn the setting ON or OFF. Dynamic Range Control (DRC):
� The default setting is OFF. � To compress the range of sound volume.
Dolby Digital :
� The default setting is Bitstream. (Bitstream : Output by Dolby Digital) (DPCM : Convert the Dolby Digital to D-PCM) Set to Bitstream when the unit is connected to Dolby Digital Decoder.
ENTER. � Select 4:3 LETTER BOX for a black bars appears on the top and bottom of the screen. � Select 4:3 PAN & SCAN for a full height picture with both sides trimmed. � Select 16:9 WIDE if a wide-screen TV is connected to the DVD player.
Panel Display: � Press K or L to select BRIGHT, DIMMER and AUTO,
then press ENTER. � This adjust the brightness of the display panel with the factory default BRIGHT. � When AUTO is selected, the display dims only during playback.
DTS:
� The default setting is OFF. Set to On when the unit is connected to DTS Decoder. (On: Output by DTS)
Angle Icon:
� Press ENTER repeatedly to turn Angle icon ON or OFF. � The default setting is ON.
MPEG:
� The default setting is OFF. (On : Output by MPEG sound) (OFF: Convert the MPEG to PCM) Set to On when the unit is connected to MPEG Decoder.
Auto Power Off:
� Press ENTER repeatedly to turn Auto Power ON or OFF. � The default setting is ON and it will turn the DVD player to off automatically after 35 minutes of no use. 4 Press SETUP to exit.
DOWN SAMPLING:
� The default setting is AUTO. � Press ENTER, then K or L to select AUTO, 48kHz or 96kHz. Press ENTER again to confirm selection. � Select 96kHz if the disc was recorded in PCM 96kHz, otherwise select 48kHz. 4 Press SETUP to exit.
Black Level Setting
Adjust the Black Level Settings to make the black parts of the picture as bright as you preferred. 1 Press MODE during playback. 2 Press ENTER repeatedly to select ON or OFF. ON: makes the dark parts brighter. OFF: shows the original picture as recorded.
NOTE:
� Black Level Setting is not available if your TV is set to receive the RGB signal (see page 8 for more infomation).
� 18 �
EN
$4.99 DVS1H SHARP Service Manual Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
|
|
|
> |
|