|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A site where discontinualed schematic diagrams and back dated information can be found on discontinued radios tv's and any electronic equipment can be found. Newer manuals either Service and operating manuals. Radio amateurs should find this site a great source for ham radio equipment manuals. I will return to this site should I need information on any electrical equipment. priced easy to download in a PDF format and print pages need to undertake the repair.
;
Quality scan of the original. All the detail necessary to troubleshoot, repair and adjust the unit. I'm sure I will be downloading more manuals in the future as the need arises.
;
Exactly as described, a Service Manual complete with the schematics and PCB layout delivered in a timely manner. Many thanks for the great service.
 ;
some of the writing is a bit blur but the part in the schmatic was great and i have fixed the machine thanks
;
Well.. I'd searched for this manual and although I found many copies online I was pleased to find your website with a well balanced pricing system and easy to search and follow links. That together with the very quick response time was just what I was looking for.. being a very impatient tech.. ;-) I had the service manual in front of me within a short time.
Bookmarked.. and you can bet I will always come here first for my service & user manuals..
best regards
Ed(Tony) Foley
G7WHK
WARNING : BEFORE SERVICING THIS CHASSIS, READ THE �X-RAY RADIATION PRECAUTION�, �SAFETY PRECAUTION� AND �PRODUCT SAFETY NOTICE� ON PAGE 3 OF THIS MANUAL.
PICTURE TUBE COMPONENTS ADJUSTMENT
DESCRIPTION OF NECK COMPONENTS
Pole 2 magnet Pole 4, 6 magnet
Deflection yoke and convergence yoke The position on the neck is required most front (CRT funnel side) and the screw is fastened after rotating yoke adjusting picture tilt. Centering magnet After adjusting picture tilt, picture position is finally fixed by this magnet. In order to get maximum margin of user convergence control for center of screen, this magnet have to be used for center convergence adjustment. PREPARATION Operate the receiver for at least 5 minutes. R, G, B CUTOFF (SCREEN VR) ADJUSTMENT 1. Adjust before replacing the SCREEN assembly. 2. Press RESET button on TV or remote hand set. 3. Call up the adjustment mode display, then adjust the data of items RCUT, GCUT and BCUT to �40�. 4. Press TV (ANT)/VIDEO button on TV. 5. Gradually rotate R, G and B SCREEN volume of FOCUS PAC (page 8) clockwise or counterclockwise until the raster appears slightly on the CRT through the each lens, and leave them. (Look into the lens in order to check the raster.) 6. Press TV (ANT)/VIDEO button on TV again. RGB ALIGNMENT & ASTIGMATISM ADJUSTMENT 1. Set the knobs of the pole 2, 4, 6 magnets of the SVM coil so that their magnetic fields override each other.
Pole 6 Pole 4
SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS
2. Enter the adjustment mode (see page 11). 3. Adjust the centering magnets for the RED, GREEN, and BLUE colors. (See CENTERING ADJUSTMENT.) 4. Press the TV/VIDEO button on the remote controller to display the internally-generated white cross dots. (White cross dots on black background. Refer to TEST SIGNAL SELECTION on page 12.) 5. Adjust the alignment and astigmatism of the projection tube for RED. (See steps (1) to (6) below. Cover the projection tubes for the other two colors with lens caps, etc.) (1) Slightly turn the focus VR of RED to the left. (2) Adjust the pole 2 magnet so that the bright section of the dot falls on the center of the dark section (flare).
Dark section (flare)
Bright section
(3) Readjust the centering magnets for the RED colors. (4) Slightly turn the focus VR of RED to the right for the sharp focus. (5) Adjust the pole 4 magnet to the desired degree so that the blurred dot becomes rectangular. (The shape should become basically same when turning the focus VR to both the left and right.)
Pole 2
�6�
|
|
|
> |
|
