|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I am very happy regarding the online purchase of this manual from Owner-Manuals.com as with this I could set right my Denon CD player and Amplifier.
I once again sincerely thank them for the prompt service which was rendered to me.
N. Shanker
;
More than pleased with my prurchase, very good product for the price.
;
Manual-link came 30 minutes after having paid for an extremely rare (40 years old) item (sony icr-120) and helped me to get the radio rework again. So really good help for me, fast and reliable delivery and -taken that into consideration- a very reasonable price for that service. So thanks again! Mike, Germany
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
TEST AND MEASUREMENT
3. 4. 5. If the carrier leakage ratio is greater than 35 dBc then unit is OK. (offset calibration is complete). If not then repeat steps 1, 2 and 3 above for Qch offset values: 87, 67, 47, 27, 7. If the carrier leakage ratio is still less than 35 dBc then unit is a fail.
Q Inc Calibration
1. 2. 3. 4. 5. Set Qch offset to 167 (see Qch Check step 2). Measure carrier leakage ratio. If carrier leakage ratio is greater than 35 dBc then unit is OK. (offset calibration is complete). If carrier leakage ratio is less than 35 dBc then repeat steps 1, 2 and 3 above for Qch offset values:187, 207, 227, 247. If carrier leakage ratio is less than 35 dBc then unit is a fail.
I, Qch Gain
IMPORTANT: I, Qch offset calibration should be done before this calibration. Spectrum Analyser Setup. centre frequency = 902.4 MHz RBW = 10 kHz VBW = 10 kHz span = 1 MHz sweep time = 2 sec 1. Set the Channel box controls to channel 62 at power level 5, normal burst modulated with all 1�s. a. Press the down arrow until CHANGE CH > is highlighted and then press ENTER. b. Press the down arrow until PL is highlighted. Press ENTER. c. Press the down arrow until TX DATA is highlighted. Press the move arrow until 1 appears in the highlighted field. Press ENTER. 2. Using the spectrum analyser measure the image leak ratio. Image leak ratio is the measured ratio of peak power and the power at 135 kHz below peak frequency.
Example: peak power (902.468 Mhz) = 33 dBm power at 135 kHz below peak power = -9 dBm image leak ratio = 33 dBm - (-9 dBm) = 42 dBm
Figure 6.31: Image leak ratio 3. 4. If image leak ratio is greater than 30 dBc then unit is OK. (offset calibration is complete). If image leak ratio is less than 30 dBc then go to Ich gain calibration.
MCUK991001C8 Service Manual
Section 6 � 49 �
Issue 1 Revision 0
|
|
|
> |
|
