ELECTROLUX EKM10420X
Owner's Manual

GB
The cookers can be set for sypply both on the right or lefthand side. In this case it is sufficient to reverse the position of the cad nipple reducer. At the end make sure than there is no leakage of gas.

INLET

STOP

A
TAB. D Values referred to Hs - 15°C - 1013,25mbar Cat. II 2H3+

B

ELECTRICAL CONNECTION This appliance must be installed by a qualified person in accordance with the latest IEE Regulations and in compliance with the manufacturer�s instructions. Check that the voltage is the same as that stated on the rating plate. The rating plate is located on the back cover. WARNING! THIS APPLIANCE MUST BE EARTHED If an fixed appliance is not equipped with supply cable and plug, the power supply must be fitted with a disconnect switch in which the distance between contacts permits total disconnection in accordance with overvoltage category III, as required by installation regulations. We recommend that the cooker circuit is rated to 20 amps. Cable type HO5 RRF 3 X 2.5 mm2 Connecting the mains cable Open the mains terminal block cover as shown, unscrew screw �A� the cable clamp, and loosen the screws in the mains terminal block �L N E� which secure the three wires of the mains cable. Fit the cable and refit screw �A�, the cable clamp. Allow sufficient cable length for the cooker to be pulled out for cleaning, but do not let it hang lower than 50mm (2�) from the floor. The cable can be looped if necessary, but make sure that it is not kinked or trapped when the cooker is in position. IMPORTANT The wires in the mains cable are coloured as follows: GREEN AND YELLOW........EARTH BLUE....................................NEUTRAL BROWN ...............................LIVE REPLACING OF THE CABLE If the cable becomes damaged or worn, replace it, observing the following instructions: - open the box of the supply board as shown in the diagram below; - unscrew screw �A� that secures the cable; - replace the cable with one of the same length and which corresponds to the features described in the table; switch the appliance off, and shut the gas tap; - connect the �green-yellow� earth wire to the terminal � �, leaving it approximately 10 mm longer than the live wire; - connect the �blue� neutral wire to the terminal marked �N�; - connect the live wire to the terminal marked �L�. GAS ADJUSTMENT Always isolate the cooker from the electricity supply, shut off the gas supply temporarily and proceed as follows. - change the injectors, - adjust the minimum flow of the burners. REPLACEMENT OF COOKTOP INJECTORS To change the cooktop injectors, proceed as follows: remove the grids, remove burners and flame-spreaders (see fig.A), change the injector (see fig.B) and replace it with another one suitable for the new type of gas (see table D). Re-assemble everything in reverse order, ensuring you position the flame-spreader correctly.
29

TABELLA GENERALE INIETTORI Kind of gas mbar Nozzle Burners Power KW Consum N° N° max. min. max. min. By pass 115 Rapide 3,00 0,75 286 l/h 72 l/h reg. NATURAL G 20 20 97 Semi rapide 1,75 72 Auxiliary 1,00 128 Triple crown 3,30 85 65 50 93
Rapide Semi rapide Auxiliary Triple crown

0,48 167 l/h 46 l/h reg. 0,33 95 l/h 31 l/h reg. 1,30 315 l/h 124 l/h reg. 0,75 219 g/h 55 g/h 42 0,48 128 g/h 35 g/h 31 0,33 73 g/h 24 g/h 27 1,30 241 g/h 95 g/h 60

BUTANE G 30 PROPANE G 31

28-30

37

3,00 1,75 1,00 3,30

MINIMUM FLOW ADJUSTMENT FOR COOKTOP TAPS To adjust the minimum, proceed as follows: switch the burner on, and turn the knob towards the minimum flow position . Remove the knob from the tap, introduce a small screwdriver in to the tap rod (fig. 11). Attention: in taps with security valve, the minimum adjustment screw �Z� is placed outside the tap rod (fig. 12).

Z

Fig. 11

Fig. 12

Loosen the adjustment screw in order to increase the flow or tighten it to decrease the flow. The proper adjustment is obtained when the flame is approximately 3 or 4 mm in length. For butane/propane gas, the adjustment screw must be fully screwed down. Make sure that the flame does not go out when passing quickly from the max. flow to the minimum flow . Assemble the knob again. APPLIANCE MAINTENANCE WARNINGS Isolate the cooker from the electricity supply before attempting to replace the oven lamp. The oven lamp is of a special type designed to withstand high temperatures. To replace it, proceed as follows: remove the protective glass (A) and replace the burnt-out bulb with one of the same type. Re-fit the protective glass.
E 14 25 W - 230 V~ T300°C

A

DISMANTLING THE COOKTOP If it becomes necessary to repair or replace internal components, proceed as follows: remove the glass lid from its position by sliding off upwards. Remove the grids, the burners and flame-spreaders (see fig. 13), unscrew the visible screws �V� located on the cooktop (see fig. 14). Dismantle the cooktop by unscrewing the 4 rear screws �A� (see fig. 15 ).