This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Top marks.
John Copeland
Glasgow
Scotland
I was so happy that the owner's manual was available. It is well written and helped me to use the radio/CD player/recorder without problems. Thanks for making it available.
Irene Lambert
Text excerpt from page 5 (click to view)
Location
Fig. 1
Fig. 4
547
550
820-870
870
600
This appliance is designed to be built-in to a space having the dimensions given in Fig. 1.
Take the hinge rem o v e d f ro m t h e upper part of the appliance on the opposite side (see Fig. 4), and, using t h e s c re w s r e m o v e d f ro m t h e
D510
820
59
6
lower part, �x it to the base of the appliance itself.
D506
100-170
Fig. 2
Remove and re�t the other hinge on the upper part of the appliance on the opposite side. Fix the two front screws into the upper and lower hinges (Fig. 4). Finally, check the alignment of the door and make sure it closes properly. After having reversed the opening direction of the door, discard the original plastic insert removed and �t the insert supplied with the appliance on the opposite side.
The height of the appliance can be altered if required by means of adjustable feet situated at its base (Fig. 2).
D507
Fitting a decorative door panel
Important: The components needed to �t the decorative panel have been pre-�tted on the appliance. The brackets are secured to the panel by means of the 7 � 3.5x13 screws supplied. Before starting to �t the panel, remove the large top bracket by unscrewing the screws and adjusting pins pre-�tted on the appliance door. The small bottom bracket need not be removed.
Fig. 5
Door reversibility
Remove the two screws which �x the upper hinge to the door.
Fig. 3
Carefully lean the appliance on its back and remove the plastic insert (Fig. 3).
A
= =
Place the appliance in the position where it is to be built in (Fig. 5). The appliance is �tted with adjustable feet; screw the front and rear feet in or
D447
Remove the two screws which �x the lower hinge to the door. Remove the four screws which �x the lower hinge to the base of the appliance and remove the hinge itself; be very careful to recover all the screws. Remove the four screws that �x the upper hinge to the appliance and remove the hinge itself.
D467
out to adjust the height of the appliance to that of the recess.
Keeping the appliance central in the recess, slide it in until its back touches the wall. With a tape measure (or similar instrument), measure distance (A) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess.
