|
|
|
Who's Online
There currently are 5971 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
;
Very comprehensive document which is a must-have for any Satellit 2100 owner whose set up is somewhat intricate. Due to the bad quality of the pictures that are rather dark and a bit blurred I gave 4-star feedback.
;
The manual was missing 2 pages but when I presented the problem to the company they made every attempt to get the 2 pages to me, when they couldn't they refunded my money. A very pleasing and easy transaction. The manual they provided was the original, it was concise and to the point. I plan to do business with this company again when should the need arise.
;
The owners manual is very good. all my how to questions were answered in detail.
Adjusting the shelves...
1. 2. 3. 4. First, remove food from shelf. Slide shelf straight out to stop. Lift front. Slide the rest of the way out.
Replacing
Shelf:
Shelf Guide
I. Fit back of shelf on top of guides with wire stops on the bottom of gurdes 2. Lrft front, slide shelf In until It clears gurde stops.
Removing crispers and crisper cover.. .
Removing the Crispers:
1 Slide crisper straight out to stop, lift front, then slrde the rest of the way out 2. Replace in the reverse order
Lift the Front, Then the Back.
Removing Cover:
1 Loftfront and remove the cover support 2. Loftout cover by pullrng up and out.
Replacing
Cover:
1 Fit back of cover into notch supports on walls of refrigerator, then lower front Into place 2. Replace cover support wrth the long tab towards the front. Note: If support needs adjustment, turn base right to lower, or left to ratse
Pull out to stop. ront and Pull Again.
Ice cube trays...
lo remove Ice:
l
Hold tray at both ends . Slightly twist
If cubes are not used, they may shrink. The movrng cold air starts a slow evaporation The longer cubes are stored, the smaller they get
Optional automatic ice maker.. .
Arm to Stop Ice Maker
l
l
It is normal for ice crescents to be attached by a corner. They ~111break apart easily You will hear water running when ice maker IS working. You�ll hear ice fall into the bin Don�t let these sounds bother you. The ice maker will not operate until the freezer IS cold enough to make Ice. This can take overnight. Because of new plumbing connections. the first Ice may be discolored or off-flavored Discard the first few batches of ice. If ice IS not being made fast enough and more ice IS needed, turn the Refrigerator Control toward a higher number. Wait a day and, if necessary, turn the Freezer Control toward A. If you remove the ice bin, raise the signal arm to shut off the ice maker. When you return the bin, push It all the way In and lower the arm to the ON position. If cubes are stated too long, they may develop an off-flavor...like stale water. Throw them away. They will be replaced. Cubes in the ice btn can also become smaller by evaporation The ice maker water supply should not be Softened water. The chemicals could damage the ice maker molds.
l
l
l
If you have the automatic Ice maker accessory or plan to add one later [Part No. ECKMF-83). there are a few things you will want to know
l
l
The ON/OFF lever IS a wire signal arm. Down...for making Ice automa-ically, Up...to shut off the Ice maker. Shake the bin occasronally to keep cubes separated, and to obtain increased storage capacity.
l l
l
6
|
|
|
> |
|
