|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
Adjusting the shelves...
I. 2. 3. 4. First, remove food from shelf. Slide shelf straight out to stop. Lrft front. Shde the rest of the way out.
Shelf Stop a
Replacing
Shelf:
I. Frt back of shelf on top of guides wrth wire stops on the bottom of gurdes. 2. Lift front, slide shelf in until It clears guide stops.
Removing crispers and crisper cover.. .
Removing the Crispers:
I, Slide crisper straight out to stop, the rest of the way out 2. Replace in the reverse order.
III?
Lift the Front, Then the Back.
front, then slide
Removing Cover:
I, Lift front and remove the cover support 2. Lift out cover by pulling up and out.
Replacing
Cover:
I, Fit back of cover into notch supports on walls of refrigerator, then lower front into place. 2. Replace cover support with the long tab towards , the front. Note: If support needs adjustment, turn base right to lower, or left to raise.
Lift the Front!r?!j%rttl?~~~:
Changing the light bulb.. .
WARNING: Before removing the light bulb, either unplug the refrigerator or disconnect the electricity leading to the refrigerator at the main power supply. Shock and injury can occur if electricity remains connected.
1. Reach behind control console to find bulb. 2. Remove bulb 3. Replace with a 40.watt appliance bulb
l l
Automatic
ice maker.. .
If you have the automatic ice maker accessory or plan to add one later (Part No. ECKMF-83), there are a few things you will want to know: lever is a wire signal arm. l The ON/OFF Down,, .for making ice automatrcally; Up...toshut off the ice maker. Shake the bin occasionally to keep cubes sepal rated, and to obtain increased storage capacity.
l
l
l
l
l
Lower
Sig;lal
\
Raise Signal Arm to Stop Ice Maker.
l
Arm to Start It.
It is normal for ice crescents to be attached by a corner. They will break apart easily. You will hear water runnrng when ice maker is working, You�ll hear ice fall into the bin. Don�t let these sounds bother you. The ice maker will not operate until the freezer IS cold enough to make ice, This con take overnight. Because of new plumbing connections, the first ice may be discolored or off-flavored. Discard the first few batches of ice. If ice is not being made fast enough and more ice is needed, turn the Refrigerator Control toward a higher number. Wait a day and, if necessary, turn the Freezer Control toward A. If you remove the Ice bin, raise the signal arm to shut off the ice maker. When you return the bin, push it all the way in and lower the arm to the ON position. If cubes are stored too long, they may develop an off-flavor...like stale water. Throw them away. They will be replaced. Cubes in the ice bin can also become smaller by evaporation. The ice maker water supply should not be softened water. The chemicals could damage the ice maker molds.
6
|
|
|
> |
|