|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was so happy that the owner's manual was available. It is well written and helped me to use the radio/CD player/recorder without problems. Thanks for making it available.
Irene Lambert
;
Excellant!!! Very quick and easy....Best $4.99 I have spent in a very long time..
I highly recommend this.
;
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
;
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
 ;
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
Reversing the door swing.. .
You can change the hinges on your refrigerator so the doors open the other way. Refer to the instruction sheet included with your refrigerator.
Removing and adjusting the freezer shelf...
To remove shelf:
1 Lift front slightly 2 Lift back off supports. 3 Replace In reverse order
To adjust shelf:
1 2 3. 4 Remove shelf Remove supports by sliding upwards Replace supports on desired level Replace shelf
Ice cube trays.. .
If cubes are not used, they may shrink The moving cold arr starts a slow evaporation. are stored, the smaller they get The longer cubes $2 To remove �. ice: 1. Hold tray at both ends 2. Slightly twist.
Optional automatic
ice maker.. .
l
If you have the automatic ice maker accessory or plan to add one later (Part No. ECKMF-83). there are a few things you will want to know: l The ON /OFF lever IS a wire srgnal arm. Down.. for making ice automatrcally: Up...to shut off the ice maker. l Shake the bin occasionally to keep cubes sepa rated, and to obtain increased storage capacity.
On
l
It is normal for Ice crescents to be attached by a corner. They will break apart easily. You will hear water running when Ice maker IS working. You�ll hear ice fall into the bin. Don�t let these sounds bother you. The ice maker will not operate until the freezer is cold enough to make ice. This can take overnight. Because of new plumbing connections. the first ice may be discolored OToff-flavored. Discard the first few batches of ice. If Ice is not being made fast enough and more ice is needed, turn the Refrigerator Control toward a higher number. Wait a day and, if necessary. turn the Freezer Control toward A. If you remove the ice bin, raise the signal arm to shut off the ice maker. When you return the bin. push it all the way in and lower the arm to the ON position. If cubes are stcxed too long, they may develop an off-flavor...like stale water. Throw them away. They WIII be replaced. Cubes In the Ice bin can alS0 become smaller by evaporation The ice maker water supply should not be softened water. The chemicals could damage the ice maker molds.
l l
l
l
l
Lower Signal Arm to Start It.
\
Raise Signal Arm to Stop Ice Maker.
l
|
|
|
> |
|
