|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
 ;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
1. Reach behind the control console 2. Remove bulb. 3. Replace with a 40-watt appliance
to find bulbs. bulb.
Removing the base grille...
To remove
METAL CLIPS
the arille:
r
SUPPORT TABS
SUPPORT TABS
1. Open the door. 2. Pull grille outwards as shown. 3. Do not remove Tech Sheet fastened grille.
behind
To replace the grille: 1. Line up grille support tabs with metal 2. Push firmly to snap into place. 3. Close the door.
clips.
Ice cube trays...
If cubes are not used, they may shrink. The moving cold air starts a slow evaporation. The longer cubes are stored, the smaller they get. ? EE:i?both 2. Slightly twist. ends
Optional
automatic ice maker...
l
If you have the automatic ice maker accessory, or if YOU plan to add one later (Part No. ECKMF-831, there are a few things you will want to know:
l
l
The ice maker will not operate until the freezer is cold enough to make ice. This can take overnight. Because of new plumbing connections, the first ice may be discolored or off-flavored. Discard the first few batches of ice. If ice is not being made fast enough and more ice is needed, turn the Refrigerator Control toward a higher number. Wait a day and, if necessary, turn the Freezer Control toward A. If you remove the ice bin, raise the signal arm to shut off the ice maker. When you return the bin, push it all the way in and lower the arm to the ON position. If cubes are stored too long, they may develop an off-flavor...like stale water. Throw them away. They will be replaced. Cubes in the ice bin can also become smaller by evaporation. Good water quality is important for good ice quality. It is not recommended that the ice maker be connected to a softened water supply. Water softener chemicals such as salt from a malfunctioning softener can damage the ice maker mold and lead to poor quality ice. If a softened water supply cannot be avoided, then it is important that the water softener be well maintained and operating properly.
The ON/OFF lever is a wire signal arm. Downfor making ice automatically. Up...to shut off the ice maker. DO NOT TURN ICE MAKER ON UNTIL IT IS CONNECTED TO THE WATER SUPPLY. The dial or lever on the side of the ice maker changes the size of the cubes Shake the bin occasionally to keep cubes separated, and to obtain increased storage capacity It is normal for ice crescents to be attached by a corner. They will break apart easily.
l
l
l
l
l
l
l
LOWER SIGNAL ARMTO : START IT
l
You will hear water running when ice maker is working. You�ll hear ice fall into the bin. Don�t let these sounds bother you.
7
|
|
|
> |
|
