|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
Notes: Screen Control FBT --- MAIN CBA F.B.T= Fly Back Transformer Use the Remote Control Unit 1. Degauss the CRT and allow CRT to operate for 20 minutes before starting the alignment. 2. Set the screen control to minimum position. Input the Black raster signal from RF input. 3. Enter the Service mode. (See page 1-4-1.) Dimmed horizontal line appears on the CRT. 4. Press the "VOL p" button. (Press "VOL p" then display will change CUT OFF/ DRIVE adjustment). 5. Choose CUT OFF/DRIVE mode then press "1" button. This adjustment mode is CUT OFF (R). 6. Press the "CH o / p" button until the horizontal line becomes white. 7. Choose CUT OFF/DRIVE mode then press "2" button. This adjustment mode is CUT OFF (G). Press "CH o / p" until the horizontal line becomes white. 8. Choose CUT OFF/DRIVE mode then press "3" button. This adjustment mode is CUT OFF (B). Press "CH o / p" until the horizontal line becomes white. 9. Input the White Raster Signal from Video In. 10.Choose CUT OFF/DRIVE mode then press "4." Adjust the RED DRIVE as needed with the "CH o / p" buttons to get the following value, X= 286, Y= 294. 11.Choose CUT OFF/DRIVE mode then press "5." Adjust the BLUE DRIVE as needed with the "CH o / p" buttons to get the following value, X= 286. 12.Turn the power off and on again.
8. Sub-Brightness Adjustment
Purpose: To get proper brightness. Symptom of Misadjustment: If Sub-Brightness is incorrect, proper brightness cannot be obtained by adjusting the Brightness Control. Test point --Tape --Adj. Point CH o / p buttons M. EQ. Pattern Generator Figure Mode --Input SYMPTE 7.5IRE Spec. See below
White
Black This bar just visible
Fig. 4
Note: SYMPTE Setup level --- 7 IRE 1. Enter the Service mode. (See page 1-4-1.) Then input SYMPTE signal from RF input. 2. Press MENU button. (Press MENU button then display will change BRT, CNT, COL, TNT and V-T). Select BRT and press "CH o / p" buttons so that the bar is just visible (See above figure). 3. Turn the power off and on again.
1-6-5
T5553EA
|
|
|
> |
|