|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Delivery came quite promptly and in a very readable format. Thank you.
;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
PREPARATION FOR USE
1 Check contents
Make in "as below". listed sure the package contains all of the accessories SUPPLIED ACCESSORIES
VCR to AV TV connection using AUDIO/VIDEO Cables
Using Optional AUDIO/ VIDEO Output Jacks With this connection, you can get better pictures and sounds when playing back a tape if your TV has A/V Input jacks. Please refer to your TV�s owner�s manual. Using AUDIO/VIDEO Input Jacks You can use the A/V input jacks on the front or the back of the VCR. � To use the input jacks on the back of the VCR, select "L1" position by pressing [0], [0], [1] on the remote control or [CHANNEL ( ) ]. � To use the input jacks on the front of the VCR, select "L2" position by pressing [0], [0], [2] on the remote control or [CHANNEL ( ) ]. �L1� or �L2� is found [Playing VCR] before the lowest
AUDIO
ACCESSORIES Coaxial Cable Remote Control Unit Batteries
PART NO. WPZ0901TM002 NA301UD/NA351UD AA x 2
2 Situate VCR
Place the VCR in a stable, horizontal surface.
3 Connect VCR to TV
VCR to TV Connection
1. Disconnect the AC power cord of the TV from the AC outlet. 2. Disconnect the antenna or cable from the TV. 3. Connect the antenna or cable to the ANT. IN jack of the VCR. 4. Connect the VCR to the TV using the coaxial cable. 5. Plug the AC power cords of the VCR and TV into the AC outlets.
[VHF/UHF combination antenna] [Indoor antenna] [Back of the VCR] [Back of the UHF/VHF combination TV]
OR
ANT IN
memorized channel. (Example: CH2)
IN
OUT
VIDEO
Audio/Video cables (not supplied) [TV A/V]
IN
L AUDIO
R VIDEO
SETTING THE CH3/CH4 SWITCH
If your TV does not have A/V terminals:
When the VCR is in the Playback mode or when the VCR is in the VCR mode, your TV will receive signals from the VCR on either channel 3 or 4. To use the VCR with your TV, set the selector switch to CH3 or CH4 (which is located in the back of your VCR), whichever is not used for normal broadcasts in CH3 CH4 your area. Then set your TV to the same channel. [Back of the VCR]
OUT
CH3 CH4
Coaxial cable (supplied)
UHF/VHF
[Cable box or satellite box]
IN
OR
OUT
From Cable or Satellite Company
OUT
SETUP
AUTOMATIC CHANNEL SET UP
You can automatically program the tuner to scan only the channels you receive in your area. � Channel memory programming is NOT needed when you connected the VCR to a cable box or satellite box as in "Connect VCR to TV". In this case, select the VCR and TV to channel 3 or 4 the same channel as the CH3 or CH4 switch on the back of the VCR. Then, the channel you want to record or view may be selected at the cable box or satellite box. � Follow the steps below once. Repeat it only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.) � You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing [EXIT/RESET].
4 Select the On Screen Language
("ENGLISH" or "ESPA�OL") by pressing [PLAY] or [STOP]. Then, press [F.FWD].
5 Begin channel preset
by pressing [F.FWD] once. The tuner scans and memorizes all active channels in your area. � The VCR distinguishes between standard TV channels and cable channels.
CH 01 AUTO SET UP
SETUP PREPARATION
6 After scanning,
the tuner stops on the lowest memorized channel. The TV screen returns to TV mode. � If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press [F.FWD] once again and the VCR will begin preset again.
1 You need to connect the antenna or cable to the VCR
first. Then, connect the VCR power plug into a standard AC outlet.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using [CHANNEL ( ) ] or directly pressing [Number] on the remote control. Note for using the Number buttons: � When selecting cable channels which are higher than 99, press [+100] first, then press the last two digits. � You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).
2 Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the VCR to match the channel selected on the TV.
3 Turn on the VCR by pressing [POWER]. It comes on that
both the POWER and the VCR/TV indicator.
�3�
EN
FOR USE
|
|
|
> |
|
