|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
;
Very fast and perfect delivery. Clear and well scanned. A lot of work professionally realized.
Again thak you a lot
 ;
This manual is accurate and of high quality. It is only volume 2 of the service manual. This is schematic, parts lists, and exploded mechanical drawings. The theory of operation and the diss-assembly instructions are in volume 1. The unit can be tricky to dis-assemble portions of so the volume 1 manual can be important. The product description of the manual is accurate but it does not say anything about volume 1 and the image of the front page does clearly say Volume 2.
;
Wellll again thank you very much fast and effective. Clear and well done for such an old TV!!!!
;
It has all the information you will need to fix it. The main circuit diagram is only A4 but being a PDF, you can print it to any size - I did it on two sheets of A3 and it didnt lose any detail - just made it readable when pinned up above the bench. I've found the fault, just need to buy some obscure bits to get it going again!
I cant fault the process, I paid for the manual in the morning and it was ready to download by lunch time.
FO-1660MTH
7. Use of Document Carrier Sheet
A document carrier sheet must be used for the following documents.
TELEPHONE JACK
A standard telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices.
� � �
Those with tears. Those smaller than size 148 mm (W) x 128 mm (L). Carbon-backed documents
�
Plugging the fax machine into a jack which is not an jack may result in damage to the machine or your telephone system. If you do not know what kind of jack you have, or needed to have one installed, contact the telephone company.
Make print straight across paper E.G. Place the document carrier in the document feeder with the clear film side down
2. Loading the imaging film (FO-15CR)
1Press the release marked OPEN and open the print compartment
cover.
�
Caution! The printing head (the strip of metal on the underside of the cover) applies heat to the printing film. It may be hot if a document has just been printed.
Direction of insertion
NOTE: To transmit a carbon-backed document, insert a white sheet of paper between the carbon back of the document and the document carrier.
�
Those containing an easily separable writing substance (e.g., tracing paper written on with a soft, heavy lead pencil).
NOTES:
� � �
When using the document carrier, carefully read the instructions written on the back. If the document carrier is dirty, clean it with a soft, moist cloth, and then dry it before using for transmission. Do not place more than one document in the carrier at a time.
[4] Installation
1. Site selection
Take the following points into consideration when selecting a site for this model.
ENVIRONMENT
� � �
The machine must be installed on a level surface. Keep the machine away from air conditioners, heaters, direct sunlight, and dust. Provide easy access to the front, back, and sides of the machine. In particular, keep the area in front of the machine clear, or the original document may jam as it comes out after scanning. The temperature should be between 5° and 35°C. The humidity should be between 30% and 85% (without condensation).
� �
2If you are replacing the imaging film, take the old film out of the print-
ing compartment and remove the three (3) green gears and the green flange from the ends of the spools. DO NOT DISCARD THE GREEN GEARS AND THE GREEN FLANGE!
ELECTRICITY
Standard local voltage, grounded AC outlet is required.
Caution!
� �
Connection to a power source other than that specified will cause damage to the equipment and is not covered under the warranty. If your area experiences a high incidence of lightning or power surges, we recommend that you install a surge protector for the power and telephone lines. Surge protectors can be purchased at most telephone specialty stores.
If the machine is moved from a cold to a warm place...
If the machine is moved from a cold to a warm place, it is possible that the reading glass may fog up, preventing proper scanning of documents for transmission. To remove the fog, turn on the power and wait approximately 2 hours before using the machine.
1�4
|
|
|
> |
|
