|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
8
8 screws as the plates withmm Secure shown. Use 6
screws for the holes marked with �A�, and 10 mm screws for the holes marked with �P�. Secure the screws in the order indicated by the numbers.
A4 A3 A3 P3 A4 A4 P4
Fixieren Sie die Platten wie in der Abbildung dargestellt mit den Schrauben. Verwenden Sie für mit �A� gekennzeichnete Löcher 6 mm Schrauben und 10 mm Schrauben für die mit �P� gekennzeichneten Löcher. Befestigen Sie die Schrauben in der Reihenfolge, in der sie nummeriert sind. Montieren Sie die rechte Seitenabdeckung des Geräts, indem Sie die Verbindungshaken in die entsprechenden �ffnungen einhängen. Befestigen Sie die längere Kassettenabdeckung an der rechten Kassettenseite, indem Sie die Verbindungshaken in die �ffnungen einhängen (zuerst oben, dann unten). Befestigen Sie die Schrauben der Seitenabdeckung des Geräts. Fixieren Sie die Kassettenabdeckung mit zwei 10 mm Schrauben. Montieren Sie die Stützplatte an die linke Geräteseite. Schieben Sie die oberen Enden der Stützplatte unter das Druckergehäuse. Stellen Sie sicher, dass die Führungen, wie in der Abbildung dargestellt, in die dafür vorgesehenen �ffnungen passen. Fixieren Sie die Platte, wie in der Abbildung dargestellt, mit den passenden Schrauben. Verwenden Sie für mit �A� gekennzeichnete Löcher 6 mm Schrauben und 10 mm Schrauben für die mit �P� gekennzeichneten Löcher. Befestigen Sie die Schrauben in der Reihenfolge, in der sie nummeriert sind. (In der rechten oberen �ffnung muss keine Schraube befestigt werden.) Montieren Sie die kürzere Kassettenabdeckung an die linke Kassettenseite, indem Sie die Verbindungshaken in die �ffnungen einhängen (zuerst oben, dann unten). Fixieren Sie die Kassettenabdeckung mit zwei 10 mm Schrauben.
Fissare le piastre con le viti come mostrato nella figura. Utilizzare viti da 6 mm per i fori contrassegnati da una �A� e viti da 10 mm per i fori contrassegnati da una �P�. Fissare le viti nell'ordine indicato dai numeri.
A2
A1
9 cover on the machine, Replace the right side
inserting the tabs into the holes.
Reinserire il coperchio laterale destro sul dispositivo, inserendo le linguette negli appositi fori.
9
Attach the longer cassette cover to the right side of the cassette, inserting the tabs into the holes (first top, then bottom).
1
Fissare il coperchio del cassetto di lunghezza maggiore al lato destro del cassetto, inserendo le linguette negli appositi fori (prima in alto, quindi in basso). Reinserire le viti nel coperchio laterale destro del dispositivo. Fissare il coperchio del cassetto con viti da 10 mm. Applicare la piastra di sostegno al lato sinistro del dispositivo, inserendo le estremità superiori della piastra sotto l'alloggiamento del dispositivo. Accertarsi che le guide si inseriscano nei fori come mostrato nella figura. Fissare la piastra con le viti come mostrato nella figura. Utilizzare viti da 6 mm per i fori contrassegnati da una �A� e viti da 10 mm per i fori contrassegnati da una �P�. Fissare le viti nell'ordine indicato dai numeri. Il foro superiore a destra non richiede l'applicazione di alcuna vite.
2
P
P
Replace the screws in the side cover on the machine. Secure the cassette cover with two 10 mm screws.
10
10
Attach the support plate to the left side of the machine, inserting the top edges of the plate under the machine housing. Make sure that the guides fit into the holes as shown. Secure the plate with screws as shown. Use 6 mm screws for the holes marked with �A�, and 10 mm screws for the holes marked with �P�. Secure the screws in the order indicated by the numbers. (Note that the top hole on the right does not require a screw.)
11 11
1
Attach the shorter cassette cover to the left side of the cassette, inserting the tabs into the holes (first top, then bottom).
Fissare il coperchio del cassetto di lunghezza minore al lato sinistro del cassetto, inserendo le linguette negli appositi fori (prima in alto, quindi in basso). Fissare il coperchio del cassetto con viti da 10 mm.
P P
2
Secure the cassette cover with two 10 mm screws.
12 12
Replace the rear cover (replace the screw under the small cover on the left side of the rear cover first, and then replace the small cover).
Montieren Sie die rückwärtige Abdeckung (fixieren Sie zuerst die Schraube unter der kleinen Abdeckung auf der linken Seite der rückwärtigen Abdeckung und dann erst die kleine Abdeckung).
Reinserire il coperchio posteriore (fissare prima la vite sotto il coperchio piccolo sul lato sinistro del coperchio posteriore, quindi reinserire il coperchio piccolo).
|
|
|
> |
|
