|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great price, Quick delivery, the document was very usefull A+++++++++++++++
;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
SPECIFICATIONS
Frequency Response (ref 1 kHz) Voltage Gain (at 1 kHz)
INPUT LINE Mic Line Link 90 dB 40 dB 20 dB OUTPUT MICROPHONE 40 dB -10 dB -30dB LINK 70 dB 20 dB -INPUT CLIPPING LEVEL AT 1kHz -62 to -6 dBV* -12 to + 44 dBV* +8 dBV 30 to 20,000 Hz, ±2 dB
Distortion
0.4% THD, 30 to 20,000 Hz at +15 dBm output; 0.5% or less IM distortion at +15 dBm output
Common Mode Rejection
65 dB minimum with input of - 20 dBV at 100 Hz
Control Interaction
Less than 1 dB with any control combination Shorting outputs, even for prolonged periods, willcause no damage; microphone input will not be damaged by signals up to 3V
Overload and Shorting Protection Phase
Inputs
INPUT Mic Line Link IMPEDANCE (at 1 kHz) FOR USE WITH 150 � less than 10 k� more than 5 k� ACTUAL 1 k� 66 k� 24 k�
All outputs in phase with input. Pin 2 is �high� with respect to pin 3; pin 1 is 2 of XLR Tips of link input and output phone jacks are in phase with pin ground. connectors.
Phantom Power
30 VDC nominal, 3.3k series resistance, automatically disabled with input switch in Line position
Operating Voltage
AC Operation: 120 or 240 VAC ± 10% (internally selectable), 50/60 Hz, 5.5W DC Operation: 27 VDC nominal at 16 mA typical no- signal, 22 mA typical at 0 VU (+4 dBm) output; 21.5 VDC minimum; battery life approximately 20 hours with alkaline batteries at +4 dBm output in continuous use; three 9 volt batteries, type NEDA 1604A (Duracell MN1604 or Eveready 522 recommended)
*Dependent on input control setting
Outputs
INPUT Mic Line Link IMPEDANCE (at 1 kHz) FOR USE WITH ACTUAL 150 � 600 � 600 � or greater 2� 185 � 100 � or less INPUT CLIPPING LEVEL AT 1kHz -34 dBV +16 dBV +16 dBV
Temperature Range
Operating: -18° to 57°C (0° to 135°F) Storage: -29° to 71°C (-20° to 160°F)
Noise
Equivalent Input Noise: -129 dBV (low-impedance microphone, 150 Ohms, 300 to 20,000 Hz) into 600 ohm load at full gain Equivalent Input Hum and Noise: -127 dBV (low-impedance microphone, 150 Ohms, 20 to 20,000 Hz) into 600 ohm load at full gain Output Noise: -90 dBV maximum (output control full counterclockwise [off]), -65 dBV maximum (output control full clockwise [on]) (input control down, 300 to 20,000 Hz) Output Hum and Noise: -75 dBV maximum (output control down), 65 dBV max. (output control up, input control down, 20 to 20,000 Hz)
Dimensions
79.5 mm H x 310 mm W x 230 mm D (3-1/8 in, x 12-7/32 in. x 9-1/16 in.)
Weight Certifications
Net: 2.75 kg (6 Ib 1 oz.) Packaged: 3.15 kg (6 Ib 15 oz.) Listed by Underwriters Laboratories. Inc.; listed by Canadian Standards Association as Certified
CONTROLS AND CONNECTORS
On�Off Switch: applies power to the FP16A circuitry Power LED: Indicates unit is on. Input Gain Screwdriver Control: adjusts input signal level. Output 1-6 Screwdriver Control: adjusts individual output channel signal levels. Norm LED: indicates when internal signal level is approximately 25 dB below clipping. Overload LED: indicates when internal signal level approaches clipping. Three-Pin XLR 1-6 Output Connectors: provide for connection to either low-impedance microphone or line level inputs of power amplifiers, mixers, or other signal processing equipment. Mic/Line 1-6 Slide Switches: select microphone or line level output signal levels. Phantom On-Off Slide Switch: applies 27 VDC (nominal) phantom power to pins 2 and 3 of the input connector for use with condenser microphones. IMPORTANT: Make certain any condenser microphone used is compatible with the FP16A phantom circuit, and that the FP16A input Mic/Line switch is in the Mic position. Do not turn the Phantom switch on when using unbalanced low-impedance microphones; objectionable hum will result. Turn the Phantom switch off when phantom power is not required. Three-Socket XLR Input connector: provides for connection to microphone or line level input signal sources. Input Mic/Line Slide Switch: selects microphone or line-level input signals. Link In, Out Phone Jacks: provide for connecting more distribution amplifiers for additional outputs, or adding external equipment such as equalizers, compressors, or limiters. When connecting two or more FP16As together for additional outputs, connect the Link Out jack of the "master" unit to the Link In jacks of the others. Any number of FP16As can be tied together in this way. The Link In jack is input-only, and has switching contacts to disconnect the input signal amplifier from the output channel volume controls. Connect an equalizer, limiter or compressor to the FP16A by connecting the FP16A Link Out jack to the external unit's input, and the external unit's output to the FP16A Link In jack. Signals at the Link jacks are typically 10 dB below line level. The Link In input impedance is greater than 20 k� and may be considered a bridging impedance.
2
|
|
|
> |
|
