|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
 ;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
Using the Powered Subwoofer
STANDBY/ON indicator VOLUME PHASE INPUT (LOW-LEVEL) INPUT (HIGH-LEVEL)
POWER
Operating the Powered Subwoofer Presetting the Volume
You need to preset the volume level of this speaker (SPPW1000) to match those of the main speakers (SPFSSD1000). Once you preset the volume level, it is stored as your reference level and the volume level of this speaker will be able to automatically change as the volume level of the Center Unit (CA-FSSD1000R) changes.
CAUTION:
� Be sure to turn off the POWER of the Powered Subwoofer when the Powered Subwoofer is not in use for an extended period of time.
INPUT Terminals
The Subwoofer has the following INPUT terminals.
INPUT(LOW-LEVEL):
Usually, the LEFT/MONO terminal is connected to the SUBWOOFER terminal of the Center Unit with the supplied signal cord. (see page 7)
1
Press the POWER button of the Subwoofer to turn on the power.
The STANDBY/ON indicator of the Subwoofer will light in green.
When the Center Unit CA-FSSD1000R is not used (Using other equipment)
If an amplifier etc. to be connected does not have the SUB WOOFER OUT terminals, the RIGHT and LEFT/MONO terminals will be connected to the LINE OUT-RIGHT and LEFT terminals of that unit.
LINE OUT RIGHT LEFT
2 3 4
Set the VOLUME of the Subwoofer in the �MIN� position. Adjust the volume of the Center Unit to your listening level. Adjust the VOLUME of the Subwoofer to balance the volume with the main speakers.
Amplifier etc.
Connecting cord (not supplied)
To turn off the Subwoofwer, press the POWER button to light off the STANDBY/ON indicator.
INPUT (HIGH-LEVEL):
You can connect the speaker output terminals of other amplifier etc. to these terminals. Connect the speaker cords in parallel to the speaker terminals on the amplifier etc.
SPEAKER RIGHT LEFT
Adding the Richness to the Bass (PHASE)
If you want to add the richness more to the bass, press the PHASE button to set it either in the �_ REVERSE� position or the �� NORMAL� position, whichever can add the richness to the bass. Normally, the PHASE button should be set in the �� NORMAL� position.
Amplifier etc.
Automatic Operating Status On/Off
To save energy, the Subwoofer enters the Standby mode if no (or very weak) sound signals come into the Subwoofer for about 5 minutes. In Standby mode, the STANDBY/ON indicator of the Subwoofer lights in red. When sound signals come in again, the Subwoofer enters the Operating mode and reproduces the sounds. The STANDBY/ON indicator will light in green again.
Speaker cords (not supplied)
� Do not use the INPUT (LOW-LEVEL) terminals and the INPUT (HIGH-LEVEL) terminals at the same time.
11
|
|
|
> |
|
