CASIO G2200-2AV
Owner's Manual

2253-2

ALARM MODE
Mode indicator

CITY CODE TABLE
City Code ADL ANC BER BKK CAI CCS CHI DAC DEL DEN DXB GUM HKG HNL IST JED JRS KBL KHI LAX LON MEX MIA MIL MLE NOU NYC PAR PPG RGN RIO ROM SEL SFO SIN SYD THR TYO WLG YVR City ADELAIDE ANCHORAGE BERLIN BANGKOK CAIRO CARACAS CHICAGO DHAKA DELHI DENVER DUBAI GUAM HONG KONG HONOLULU ISTANBUL JEDDAH JERUSALEM KABUL KARACHI LOS ANGELES LONDON MEXICO CITY MIAMI MILAN MALE NOUMEA NEW YORK PARIS PAGO PAGO YANGON RIO DE JANEIRO ROME SEOUL SAN FRANCISCO SINGAPORE SYDNEY TEHRAN TOKYO WELLINGTON VANCOUVER GMT differential +9.5 �09 +01 +07 +02 �04 �06 +06 +5.5 �07 +04 +10 +08 �10 +02 +03 +02 +4.5 +05 �08 +00 �06 �05 +01 +05 +11 �05 +01 �11 +6.5 �03 +01 +09 �08 +08 +10 +3.5 +09 +12 �08

PM indicator Minutes Hour

When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset time each day. Press any button to stop the alarm after it starts to Alarm on sound. When the Hourly Time Signal is turned on, indicator the watch beeps every hour on the hour. Hourly � The alarm sounds when the time selected for basic time timekeeping in the Timekeeping Mode (TIME 1 or signal on TIME 2) matches the alarm time you set.
indicator

To set the alarm time
1. Hold down A while in the Alarm Mode. The hour digits flash on the display because they are selected. At this time the Daily Alarm is turned on automatically. 2. Press C to change the selection in the following sequence.
Hour Minutes

Current time

3. Press D to increase the selected digits and B to decrease them. Holding down either button changes the selection at high speed. � The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping. � When setting the alarm time using the 12-hour format, take care to set the time correctly as morning (no indicator) or afternoon (P). 4. After you set the alarm time, press A to return to the Alarm Mode. � If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Alarm Mode automatically.

To switch the daily alarm and hourly time signal on and off
Press D while in the Alarm Mode to change the status of the daily alarm and hourly time signal in the following sequence.
Alarm on indicator Hourly time signal on indicator

Both ON

Both OFF

Daily Alarm Only

Hourly Time Signal Only

To test the alarm
Hold down D while in the Alarm Mode to sound the alarm.

STOPWATCH MODE
Mode indicator
The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 59 minutes, 59.99 seconds.

Current time Minutes Seconds 1/100 seconds
D Start D Start D Start

*Based on data as of December 1997.

(a) Elapsed time measurement

�D

�D
Re-start

�D
Stop

�

Stop

A Clear A Clear A Clear

(b) Split time measurement

�A

�A
Split release

�D
Stop

�

Split

(c) Split time and 1st-2nd place times

�A

�D

�A
Split release Record time of second runner.

�

Split First runner finishes.

Stop Second runner finishes. Record time of first runner.

AUTO DISPLAY FUNCTION
The Auto Display function of this watch continually changes the contents of the display. Note that you cannot use any of the watch�s other functions while the Auto Display function is operating.

To turn the Auto Display on
Hold down C for about two or three seconds in any mode until the watch beeps.

To turn the Auto Display off
Hold down C for about two or three seconds until the watch beeps. At this time the watch is in the Timekeeping Mode. Note The Auto Display function cannot be performed while you are making settings (i.e. while digits or other setting are flashing on the display).