|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
;
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
0$,17(1$1&( $1' 6(59,&,1* *(1(5$/ $ 5(029$/ 2) '(%5,6 25 6227 '(326,76
Allow the appliance to cool sufficiently before removing all of the coals and firebed components for cleaning purposes. Once all the ceramics are removed from the firebed check that no debris is located in the burner slots (both front and rear). If any debris is present it may easily be removed by using a small piece of thin cardboard to ease out any foreign matter. Be sure to remove the cardboard after use. Any sooty deposits or debris left on the coals may be removed by using a soft brush or by careful use of a vacuum cleaner. Any sooty deposit on the thermocouple probe can be cleaned off using a non-fluffy cloth. DO NOT USE ABRASIVE MATERIALS % 6(59,&,1* &20321(176 %(/2: 7+( %851(5 $66(0%/<
TURN OFF THE GAS SUPPLY TO THE APPLIANCE. Remove coals, coal supports, burner inserts and front simulated coal. To gain access to components below the burner assembly it has to be removed from the vent box case by disconnecting the gas supply at the inlet elbow and unscrewing the two screws at the base of the facia panel. Where the supply is fed from the right hand side across the front of the fire it will be necessary to disconnect the supply from the isolation tap/elbow. I. TO CLEAN OR REPLACE THE INJECTOR: Unscrew the compression nut connecting the gas supply to the elbow injector while supporting the injector. This is to prevent distortion of the framework, unscrew and remove the gas supply tube from the gas control valve, hold the injector lock nut with a spanner and rotate the injector. Replace in reverse order. TO REPLACE THE GAS CONTROL (Tap/FSD): Disconnect the three gas pipes and the thermocouple from the control. Pull off the knob and lay to one side. Undo the retaining nut at the front of the tap niting assembly to withdraw control from the mounting bracket. Replace in reverse order. TO REPLACE THE PIEZO IGNITER: Pull off the HT lead from the rear of the igniter, prevent the metal fixing nut from turning, rotate the body of the igniter to unscrew and withdraw the igniter from the front. Replace in reverse order and reconnect the HT lead. TO REPLACE THE OXY-PILOT ASSEMBLY: The operation of the oxy-pilot depends on the proximity of the spark electrode and the thermocouple tip, if either of these components are defective the assembly must be replaced. This is achieved by removing the tube nut from the base of the pilot and the thermocouple from the FSD also the igniter lead and the two M4 screws securing the bracket to the framework. Replace in reverse order, the spark gap is shown in Fig 18. TO REPLACE THE FILTER ASSEMBLY: Unscrew and remove the tube nut and tube at the base of the oxypilot assembly, the filter is located in the bottom of the assembly. Replace in reverse order, see Fig 18.
II.
III.
IV.
V.
Page 9
|
|
|
> |
|
