|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
complete part-lists and pcb layout, schematic diagram is good enlargable,
;
Excellent, fast delivery, excellent product. Good luck!
;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
GM-X922, GM-X1022
22
Three-channel mode, two-way system Connecting the Speaker
wires Output Terminals
The speaker output mode can be two-chan-
1. Expose end of the speaker wires Mid-high (Left) nel (stereo), one-channel (mono), or threeC1
speaker leads suit the mode according to nippers or a cutter. figures on the following pages.
Twist � When connecting to the speaker input, do not connect the RCA output. C1 Mid-high (Right) � When connecting to the RCA input, do not
by about 10 mm and twist using channel (stereo + mono). Connect the
L1 Woofer (Mono)
10 mm connect the speaker input.
Fig.
Two-channel mode (stereo) Three-channel mode, three-way system 2. Attach lugs to speaker wire ends.
Fig. 22 16
Lugs not supplied. High/mid-high
L2 C2
� Use pliers, etc., crimp lugs to wires. C1 (Left) (Left) Woofer/sub-woofer wire Speaker (Mono) (Right)
Lug Mid/mid-bass (Left)
L1
Fig. 17 C2 Mid/mid-bass L2 Fig. 20 (Right)
3. Connect speaker wires to the
High/mid-high
speaker output terminals. (Right) Fig. 23 � Fix speaker wires securely with the termi� Inductors (L1 and L2 in the diagrams) � After pass through the terminal cover, conact as low-pass filters. Capacitors (C1 nect the terminal and C2 in the diagrams) act as high-pass woofer/sub-woofer, and capacitors (C)
Speaker (Mono) are used for the high/mid-high.
One-channel mode (mono)
nal screws.
Terminal screw filters. Inductors (L) are used for the
� Remember when bridging an amplifier it will see only half of the original speaker Terminal cover Fig. 21
wire Speaker impedance. Therefore, you must use
output speakers that have ratings of 4 ohms or terminal higher. If you use speakers that have
Three-channel mode (stereo + mono) damage to the amplifier.
lower impedance ratings it may cause
4. Cover the terminals. but three channels can be achieved by solder them so they cannot be pulled
Fig. 18 channel/one-channel bridgeable amplifier, connected to the speaker wires, secure or
The power amplifier is basically a two� When the inductors and capacitors are
combining the stereo and mono modes loose. Tape or use heat shrink on the using inductors and capacitors. joints to prevent short circuits.
Fig. 19
|
|
|
> |
|
