|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It's a grate service manuals.Have many details and the writing it's so clear.You have all you want in manual,nothing missing,belive me.I'm verry satisfied of this manual.
;
Great scanned service manual
Usefull informations.
I will buy again!
Best Regards
;
The manual describes this product very good. It has the basic things to know and also a more detailed look. Very well made!
;
An excellent document to assist in the repair of my old personal tape player. It includes full circuit diagrams and physical layout drawings and full instructions on disassembly and fault finding.
Well worth the meagre price.
;
Very good conversation, Pretty fast Service, wood do it again,
Have paid by Paypal, so i got the Service Manual online after 15 Min.
Very helpfully.
Greeting from Germany,
Hans
CONNECTING THE SPEAKER WIRES
(1) GM-X422/X1R/UC, GM-X322/X1R/UC (2) GM-X422/X1R/ES
two-chanThree-channel mode, two-way system The speaker output mode can be two-channel (stereo), one-channel (mono). nel (stereo), one-channel (mono), or threeTo connect speaker leads to suit mode. Connect the speakers channel (stereo + mono). To connect according to figures on the following pages.
� When connecting to speaker input, do not connect the RCA output. speaker leads to suit mode. Connect the � When connecting to RCA input, do not connect the speaker input. speakers according to figures on the folMid-high (Left) � When connecting to the speaker input, do not Speaker input
C1 Mid-high (Right)
lowing pages. C1 Two-channel (stereo) One-channel mode (mono)
(Right) � When connecting to the RCA input, do not L1 connect the speaker input. (Left)
connect the RCA output.
Woofer (Mono)
Two-channel mode (stereo)
Three-channel mode, three-way system
C1 (Left) Speaker (Mono) (Left)
(Right) Fig. 20 Speaker input (Left) High/mid-high Speaker (Right) Mid/mid-bass
L2 C2
(Left)
L1
22 Fig. 23 (Left) Woofer/sub-woofer
Speaker (Mono) (Right)
Fig. 18 (Right)
High/mid-high (3) GM-X422/X1R/EW One-channel mode (mono) (Right)
Mid/mid-bass L2 C2
(Right) The speaker output mode can be two-channel (stereo), one-channel Fig. 21 Speaker input (mono). To connect speaker leads to suit mode. Connect the speak� The inductor (L1 or L2 in the diagram) (Left) ers according to figures on the following pages.
acts as a low-pass filter. The capacitor (C1 or C2 in the diagram) acts as a highpass filter. The inductor (L) shall be used Two-channel (stereo) One-channel mode (mono) on the woofer/sub-woofer, and that a capacitor (C) shall be used on the high/mid-high.
Speaker (Mono)
Speaker (Mono) � Remember when bridging an amplifier it
Three-channel mode (stereo + Speaker speakers that have ratings of 4 ohms or mono)
lower impedance ratings it may cause channel/one-channel bridgeable amplifier, damage to the amplifier. but three channels can be achieved by combining the stereo and mono modes connected to the speaker wires, secure or using inductors and capacitors. solder them so they cannot be pulled loose. Tape or use heat shrink on the joints to prevent short circuits.
will see only half of the original speaker Fig. 19 impedance. Therefore, you must use (Left) higher. If you use speakers that have
(Right)
The power amplifier is basically a two-
GM-X422, GM-X322
24 Fig. 25
� When the inductors and capacitors are
19
|
|
|
> |
|
