|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
 ;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
;
The product manual I received was exactly what I was looking for, delivered painlessly at a very fair price. I can't ask for any more than that.
;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
Self-diagnostic Indication
When something abnormal occurs with the Monitor, this function informs you of the condition of the Monitor with self-diagnostic lamps, allowing for smooth service work.
Remote sensor 1 2 3 Power lamp Self-diagnostic lamps (1 to 3)
MENU INPUT
If the trouble still persists, follow the procedure below:
1
Check which lamps are lighting or flashing.
On the Self-diagnostic Report Sheet (below), check the box next to �Lights� or �Flashes� of the corresponding lamp or lamps. � Only one lamp may light or flash, or all three lamps may do so.
2 3 4
Switch off the POWER switch on the back of the Monitor. Unplug the power cord. Call your dealer and tell which lamps are lighting or flashing. (Copy and fax the Self-diagnostic Report Sheet below.)
� If the screen monitor turns off and self-diagnostic lamps light or flash
If the self-diagnostic lamps light or flash in red, check the following before consulting the dealer where you purchased the Monitor. � If self-diagnostic lamp 1 (upper) flashes, lamp 2 (middle) lights, and lamp 3 (lower) flashes This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. � After cleaning, switch on the Monitor�s main power again. If self-diagnostic lamps do not go off, consult your dealer immediately.
Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual.
Self-diagnostic Report Sheet
Store name where you purchased the Monitor
� If the screen monitor dims a little and �TEMP. OVER� lights (or flashes)
If �TEMP. OVER� lights or flashes at the right bottom of the screen, check the following before consulting the dealer where you purchased the Monitor. �TEMP. OVER� appears to warn you of the internal heat buildup, which is usually caused by accumulated dust around the intakes or by improper installation. If the cause of the internal heat buildup is eliminated, this indication disappears and the screen recovers the brightness. � If �TEMP. OVER� flashes in yellow This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. � After cleaning, switch on the Monitor�s main power again. If �TEMP. OVER� still flashes, this trouble may be caused by improper installation or improper location of the Monitor. In this case, consult your dealer immediately to solve this improper installation and to improve the circumstances around the Monitor. � If �TEMP. OVER� lights in red �TEMP. OVER� will be shown for abut two minutes, the Monitor will shut off automatically, then the Selfdiagonal lamps light in red. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then consult your dealer immediately.
To
Model Name: Plasma Display Monitor GM-X50S
The self-diagnostic lamps light or flash as listed on the following table. Please give me immediate advice or service if necessary.
Self-diagnostic lamps
NO. Lamp position 1 2 3 Upper Middle Lower TEMP. OVER
Conditions
& Lights & Lights & Lights & Lights
& Flashes & Flashes & Flashes & Flashes
Your Name: Telephone No.: Address:
37
ENGLISH
|
|
|
> |
|
