|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A very easy to understand and use manual. Well worth the money.
 ;
Very good information with clear drawings. Thanks!
;
The ease of this purchase was a good start. The content of this manual was exactly all I needed to retore my Tandberg 64.
All of the mechanical and electrical information is contained in the manual and the quality of the document makes reading the data easy.
The exerience with the resource has made this my prime source for technical data.
;
Owner-manuals.com is the best Possibility to give vantage HIGH CLASS Elektronic COMPONENTS
a new Life.Thanks alot for your perfekt Service.
;
I am proud of you. In the future, I benefited from your services.
Connection Diagram SPECIFICATIONS
Fuse (30 A)
Grommet
Fuse (30 A) Dimensions . 255 (W) 61 (H) � 310 (D) mm Ground wire (black) [RD-223] (sold separately). . [10 (W) 2-3/8 (H) � 12-1/4 (D) in.] Connect to metal body or chassis. Weight . 4.1 kg (9.0 lbs.) (Leads for wiring not included) Maximum power output . 100 4 / 240 W � 2 (EIAJ) Continuous power output 50 W � (at 14.4V, 4 �, 20 � 20,000 Hz, 0.08% THD) . 120 W � 2 (at 14.4V, 4 �, 20 � 20,000 Hz, 0.8% THD) RCA input jacks Load impedance . 4 (1 � 8 � allowable) Connecting wires with RCA . (Bridge connection: 2 � 8 � allowable) Frequency response . 10 � 50,000 Hz (+0 dB, �1 dB) pin plugs (sold separately). Signal-to-noise ratio . 105 dB (IHF�A network)
Power source . 14.4 DC (10.8 � 15.1 V allowable) Grounding system . Negative type Special red battery wire [RD-223] (sold separately). Current consumption . 29 A (at continuous power, 4 �) After making all other connections at the amplifier, Average current drawn* . 8 A (4 � for four channels) connect battery wire terminal of the amplifier to . 12.5 A (4 � for two channels) positive (+) terminal of the battery. Fuse . 20 A � 2
RCA input Amplifier with . 60 W � 4 (at 14.4V, 2 �, 20 � 20,000 Hz, 0.8% THD)
Car stereo with Distortion . 0.004% (10 W, 1 kHz) Separation . 70 dB (1 kHz) RCA output jacks
External Output Low pass filter . Cut off frequency: 50 � 120 Hz For details on how connect to . Cut off slope: �12 dB/oct RCA input jacks A and B, see the High pass filter . Cut off frequency: 50 � 120 Hz �Connecting the Speakers and Input . Cut off slope: �12 dB/oct wires� section. Input level / impedance . RCA: 0.4 � 4.0 V/22 k� If only one input plug is used, do not . Speaker: 1.6 � 10 V/78 k� connect anything to RCA input jack B. Note: � Specifications and the design are subject to possible modification without notice due to improvements.
output RCA input jack A, B � The average current drawn is nearly the maximum cur-
*Average current drawn Reverse
rent drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
Connecting wires with RCA pin plugs (sold separately).
Fuse (20 A) � 2
GM-X624, GM-X524
Speaker output terminal Blue [RD-223] (sold separately). See �Connecting Connect male terminal of this wire to the blue Speakers and Input wire of the car stereo (SYSTEM REMOTE CONwires� section for speakTROL). The female terminal can be connected to er connection instrucauto-antenna relay control terminal. If the car tions. stereo does not have a system remote control terminal, connect male terminal to the power terminal through the ignition switch.
21
|
|
|
> |
|
