|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very detailed product, also it is a scanning from original, very useful if you have to service this type of amplifier ! Very good product, very hard to find!
;
the Manual was made available as promised, the scans were excellent..Good Work !!!
;
It's complete and helpful manual with good quality of scan. Thanks very much.
;
The service was quick and simple, finding the service manual easy and it appears to be the original with colour schematics. It contained the info I was after and so sorted the problem.
I have copied it to CD and attached the envelope to the inside back cover of the owners manual. Good manual and excelent service. Robin Wood, Wood Electronics, New Zealand.
;
Exactly what was needed to assess the product - excellent value and great service
Connection Diagram SPECIFICATIONS
Fuse (30 A)
Grommet
Fuse (30 A) Dimensions . 255 (W) 61 (H) � 310 (D) mm Ground wire (black) [RD-223] (sold separately). . [10 (W) 2-3/8 (H) � 12-1/4 (D) in.] Connect to metal body or chassis. Weight . 4.1 kg (9.0 lbs.) (Leads for wiring not included) Maximum power output . 100 4 / 240 W � 2 (EIAJ) Continuous power output 50 W � (at 14.4V, 4 �, 20 � 20,000 Hz, 0.08% THD) . 120 W � 2 (at 14.4V, 4 �, 20 � 20,000 Hz, 0.8% THD) RCA input jacks Load impedance . 4 (1 � 8 � allowable) Connecting wires with RCA . (Bridge connection: 2 � 8 � allowable) Frequency response . 10 � 50,000 Hz (+0 dB, �1 dB) pin plugs (sold separately). Signal-to-noise ratio . 105 dB (IHF�A network)
Power source . 14.4 DC (10.8 � 15.1 V allowable) Grounding system . Negative type Special red battery wire [RD-223] (sold separately). Current consumption . 29 A (at continuous power, 4 �) After making all other connections at the amplifier, Average current drawn* . 8 A (4 � for four channels) connect battery wire terminal of the amplifier to . 12.5 A (4 � for two channels) positive (+) terminal of the battery. Fuse . 20 A � 2
RCA input Amplifier with . 60 W � 4 (at 14.4V, 2 �, 20 � 20,000 Hz, 0.8% THD)
Car stereo with Distortion . 0.004% (10 W, 1 kHz) Separation . 70 dB (1 kHz) RCA output jacks
External Output Low pass filter . Cut off frequency: 50 � 120 Hz For details on how connect to . Cut off slope: �12 dB/oct RCA input jacks A and B, see the High pass filter . Cut off frequency: 50 � 120 Hz �Connecting the Speakers and Input . Cut off slope: �12 dB/oct wires� section. Input level / impedance . RCA: 0.4 � 4.0 V/22 k� If only one input plug is used, do not . Speaker: 1.6 � 10 V/78 k� connect anything to RCA input jack B. Note: � Specifications and the design are subject to possible modification without notice due to improvements.
output RCA input jack A, B � The average current drawn is nearly the maximum cur-
*Average current drawn Reverse
rent drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
Connecting wires with RCA pin plugs (sold separately).
Fuse (20 A) � 2
GM-X624, GM-X524
Speaker output terminal Blue [RD-223] (sold separately). See �Connecting Connect male terminal of this wire to the blue Speakers and Input wire of the car stereo (SYSTEM REMOTE CONwires� section for speakTROL). The female terminal can be connected to er connection instrucauto-antenna relay control terminal. If the car tions. stereo does not have a system remote control terminal, connect male terminal to the power terminal through the ignition switch.
21
|
|
|
> |
|
