|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Impeccable, document très complet. Perfect, i get all i need. All schematic are correct. Thanks
;
The manual is of better quality compared to other. I found it less expensive and therefore it it is the best buy cost vs quality.
 ;
I bought the service-manual of the sony ICB-1020(an old transmitter-receiver) at "www.Owners-Manual.com", I found the service-manual for a fairly cheap price(in comparison with other sellers). I filled in some questions, payed the order with Ideal, and within 24 hours I had my service manual. I was very happy:In no time I had my service-manual and everything, but literally everything was noted down in the manual; the electronic scheme, the parts list, etcetera.
A very practical, reference-document.
;
This comprehesive service maual was greatly appreciated, as was the digital download.
;
Good en helpfull black and white scanned Srfvice manual of the Philps D8444. Quick service and delivery
Connection Diagram SPECIFICATIONS
Fuse (30 A)
Grommet
Fuse (30 A) Dimensions . 255 (W) 61 (H) � 310 (D) mm Ground wire (black) [RD-223] (sold separately). . [10 (W) 2-3/8 (H) � 12-1/4 (D) in.] Connect to metal body or chassis. Weight . 4.1 kg (9.0 lbs.) (Leads for wiring not included) Maximum power output . 100 4 / 240 W � 2 (EIAJ) Continuous power output 50 W � (at 14.4V, 4 �, 20 � 20,000 Hz, 0.08% THD) . 120 W � 2 (at 14.4V, 4 �, 20 � 20,000 Hz, 0.8% THD) RCA input jacks Load impedance . 4 (1 � 8 � allowable) Connecting wires with RCA . (Bridge connection: 2 � 8 � allowable) Frequency response . 10 � 50,000 Hz (+0 dB, �1 dB) pin plugs (sold separately). Signal-to-noise ratio . 105 dB (IHF�A network)
Power source . 14.4 DC (10.8 � 15.1 V allowable) Grounding system . Negative type Special red battery wire [RD-223] (sold separately). Current consumption . 29 A (at continuous power, 4 �) After making all other connections at the amplifier, Average current drawn* . 8 A (4 � for four channels) connect battery wire terminal of the amplifier to . 12.5 A (4 � for two channels) positive (+) terminal of the battery. Fuse . 20 A � 2
RCA input Amplifier with . 60 W � 4 (at 14.4V, 2 �, 20 � 20,000 Hz, 0.8% THD)
Car stereo with Distortion . 0.004% (10 W, 1 kHz) Separation . 70 dB (1 kHz) RCA output jacks
External Output Low pass filter . Cut off frequency: 50 � 120 Hz For details on how connect to . Cut off slope: �12 dB/oct RCA input jacks A and B, see the High pass filter . Cut off frequency: 50 � 120 Hz �Connecting the Speakers and Input . Cut off slope: �12 dB/oct wires� section. Input level / impedance . RCA: 0.4 � 4.0 V/22 k� If only one input plug is used, do not . Speaker: 1.6 � 10 V/78 k� connect anything to RCA input jack B. Note: � Specifications and the design are subject to possible modification without notice due to improvements.
output RCA input jack A, B � The average current drawn is nearly the maximum cur-
*Average current drawn Reverse
rent drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
Connecting wires with RCA pin plugs (sold separately).
Fuse (20 A) � 2
GM-X624, GM-X524
Speaker output terminal Blue [RD-223] (sold separately). See �Connecting Connect male terminal of this wire to the blue Speakers and Input wire of the car stereo (SYSTEM REMOTE CONwires� section for speakTROL). The female terminal can be connected to er connection instrucauto-antenna relay control terminal. If the car tions. stereo does not have a system remote control terminal, connect male terminal to the power terminal through the ignition switch.
21
|
|
|
> |
|
