|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
GM-X922, GM-X1022
22
Three-channel mode, two-way system Connecting the Speaker
wires Output Terminals
The speaker output mode can be two-chan-
1. Expose end of the speaker wires Mid-high (Left) nel (stereo), one-channel (mono), or threeC1
speaker leads suit the mode according to nippers or a cutter. figures on the following pages.
Twist � When connecting to the speaker input, do not connect the RCA output. C1 Mid-high (Right) � When connecting to the RCA input, do not
by about 10 mm and twist using channel (stereo + mono). Connect the
L1 Woofer (Mono)
10 mm connect the speaker input.
Fig.
Two-channel mode (stereo) Three-channel mode, three-way system 2. Attach lugs to speaker wire ends.
Fig. 22 16
Lugs not supplied. High/mid-high
L2 C2
� Use pliers, etc., crimp lugs to wires. C1 (Left) (Left) Woofer/sub-woofer wire Speaker (Mono) (Right)
Lug Mid/mid-bass (Left)
L1
Fig. 17 C2 Mid/mid-bass L2 Fig. 20 (Right)
3. Connect speaker wires to the
High/mid-high
speaker output terminals. (Right) Fig. 23 � Fix speaker wires securely with the termi� Inductors (L1 and L2 in the diagrams) � After pass through the terminal cover, conact as low-pass filters. Capacitors (C1 nect the terminal and C2 in the diagrams) act as high-pass woofer/sub-woofer, and capacitors (C)
Speaker (Mono) are used for the high/mid-high.
One-channel mode (mono)
nal screws.
Terminal screw filters. Inductors (L) are used for the
� Remember when bridging an amplifier it will see only half of the original speaker Terminal cover Fig. 21
wire Speaker impedance. Therefore, you must use
output speakers that have ratings of 4 ohms or terminal higher. If you use speakers that have
Three-channel mode (stereo + mono) damage to the amplifier.
lower impedance ratings it may cause
4. Cover the terminals. but three channels can be achieved by solder them so they cannot be pulled
Fig. 18 channel/one-channel bridgeable amplifier, connected to the speaker wires, secure or
The power amplifier is basically a two� When the inductors and capacitors are
combining the stereo and mono modes loose. Tape or use heat shrink on the using inductors and capacitors. joints to prevent short circuits.
Fig. 19
|
|
|
> |
|
