|
Who's Online
There currently are 5903 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
Note: The shape of the monitor assembly varies by the size of the LCD screen. For the 3.5�-type LCD, refer to Fig. 1-4-2. 1.4.3 Disassembly/assembly of monitor assembly (for 3.5�-type LCD) Note: Be careful not to soil or scratch the monitor screen through the disassembly/assembly work. 1. Remove the four screws (1 to 4) in numerical order. While disengaging the six hooks (L4a to L4f) in alphabetical order, remove the monitor cover assembly. Note4f: When removing the monitor cover assembly, be
3. Unplug the wires and FPCs from the two connectors ( c , d ), and then remove the LCD BL board assembly, holder (PWB) and backlight in that order. 4. Remove the LCD module while disengaging it from the four hooks (L4g, L4h, L4j, L4k,). 1.4.4 Disassembly/assembly of hinge assembly (for 3.5�-type LCD) 1. Remove the three screws (5 to 7), and then remove the hinge covers (1) and (2) by disengaging a total of four hooks (L4m, L4n) at the two sides. 2. Separate the SW board assembly and the FPC from the hinge assembly. Note4j: When disassembling/assembling the hinge assembly, pay careful attention to every part not to damage anything. Note4k: When connecting the FPC, arrange the FPC wire by winding it around the shaft (hinge pin) of the hinge assembly by two and a half turns while paying heed to the orientation of the hinge assembly and FPC.
(L 4 c) (L 4 f) (L 4 e)
careful not to damage the FPC and connector.
2. Unlock the connector b and then disconnect the FPC while lifting the hinge assembly upwards to remove it together with the FPC. Note4g: For disconnecting the FPC, unlock the connector first and then lift the hinge assembly upwards. Accordingly, the FPC is disconnected together with the hinge assembly. Note4h: Treat the wires carefully.
� : 0.069N·m (0.7kgf·cm) �� : 0.098N·m (1.0kgf·cm) ��� : 0.147N·m (1.5kgf·cm)
Hinge cover(1) 6� (S 4 d) c MONI. FPC ASSY Note 4 j/ 4 k 5� (S 4 c) (L 4 n) c Note 4 j / 4 k Hinge cover(2) b (L 4 m) 7� (S 4 d)
Monitor cover assy
(L 4 b)
3 (S 4 b)
���
a
4��� (S 4 b) c (L 4 a)
(L 4 d) 1�� (S 4 a)
2�� 4 (S a)
LCD BL PWB d Note 4 f a NoteHinge 4 k 4 j/ assy Note 4 g b
Holder (PWB)
FPC
Back light LCD module
Hinge
Note 4 h 3.5� 4 (L 4 j) (L 4 h) Monitor case assy
(L
k) (L 4 g) b
Bracket(Earth)
a
Fig. 1-4-2 1-8
|
|
|
> |
|