|
Who's Online
There currently are 6030 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
3. 4 REEL DISK ASSY(SUP) 5 REEL DISK ASSY(TU) 6 REEL COVER ASSY NOTE4:
(W 4 ) NOTE 4 4 8 (S 6 a) (W 6 )
WHITE BLACK
(W 5 ) NOTE 5 5 10 (S 6 b) 9 (S 6 a)
Be careful not to attach the REEL DISK wrongly. The Supply side can be identified by the white color at the center.
NOTE 4 , 5
NOTE5: Be careful not to attach the REEL DISK wrongly. The Take-up side can be iden-
REEL DISK ASSY
(W 6 )
tified by the black color at the center.
NOTE6: Perform the following steps for mounting. 1. Align the 2 holes with the pins. 2. Attach the PINCH ROLLER ARM ASSY by aligning the positions. 3. Attach the SUB DECK NOTE 6 ASSY by aligning the 3 5 2,6 positions. 4. Check that the parts below them are located in the correct positions. 4
SUP TU
6 NOTE 6
5. Tighten the 2 screws. 6. Tighten the screw. 7. Attach the 2 SLIT WASHER parts.
4. 7 TENSION ARM ASSY 8 SLANT POLE ARM ASSY 9 TU ARM ASSY 0 SWING ARM ASSY NOTE7: When detaching, remove the spring of the @ PAD ARM ASSY in advance. Pay attention to the attachment po-
1, 7
Fig. 2-4-5
NOTE 7
8 NOTE 7
SPRING
NOTE 8
(P 8 ) NOTE 8 NOTE 10 10
7
11 (S 10 )
NOTE 9 9
sition.
NOTE8:
A
When mounting the SLANT POLE ARM ASSY, hook the spring onto the lug as in diagram A, and fit the combination onto the SLIDE DECK ASSY. After fitting, hook the spring onto the lug of the SLIDE DECK ASSY as in diagram B. Be careful not to lose the spring.
SPRING
B
NOTE 7
NOTE 9
NOTE9: Pay attention to the mounting position.
NOTE0: When detaching, remove the screw
NOTE 10
Fig. 2-4-6
then remove the SWING ARM ASSY by pulling it up and turning it.
2-8
|
|
|
> |
|