|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
3. 4 REEL DISK ASSY(SUP) 5 REEL DISK ASSY(TU) 6 REEL COVER ASSY NOTE4:
(W 4 ) NOTE 4 4 8 (S 6 a) (W 6 )
WHITE BLACK
(W 5 ) NOTE 5 5 10 (S 6 b) 9 (S 6 a)
Be careful not to attach the REEL DISK wrongly. The Supply side can be identified by the white color at the center.
NOTE 4 , 5
NOTE5: Be careful not to attach the REEL DISK wrongly. The Take-up side can be iden-
REEL DISK ASSY
(W 6 )
tified by the black color at the center.
NOTE6: Perform the following steps for mounting. 1. Align the 2 holes with the pins. 2. Attach the PINCH ROLLER ARM ASSY by aligning the positions. 3. Attach the SUB DECK NOTE 6 ASSY by aligning the 3 5 2,6 positions. 4. Check that the parts below them are located in the correct positions. 4
SUP TU
6 NOTE 6
5. Tighten the 2 screws. 6. Tighten the screw. 7. Attach the 2 SLIT WASHER parts.
4. 7 TENSION ARM ASSY 8 SLANT POLE ARM ASSY 9 TU ARM ASSY 0 SWING ARM ASSY NOTE7: When detaching, remove the spring of the @ PAD ARM ASSY in advance. Pay attention to the attachment po-
1, 7
Fig. 2-4-5
NOTE 7
8 NOTE 7
SPRING
NOTE 8
(P 8 ) NOTE 8 NOTE 10 10
7
11 (S 10 )
NOTE 9 9
sition.
NOTE8:
A
When mounting the SLANT POLE ARM ASSY, hook the spring onto the lug as in diagram A, and fit the combination onto the SLIDE DECK ASSY. After fitting, hook the spring onto the lug of the SLIDE DECK ASSY as in diagram B. Be careful not to lose the spring.
SPRING
B
NOTE 7
NOTE 9
NOTE9: Pay attention to the mounting position.
NOTE0: When detaching, remove the screw
NOTE 10
Fig. 2-4-6
then remove the SWING ARM ASSY by pulling it up and turning it.
2-8
|
|
|
> |
|
