|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
El producto satisface las necesidades del servicio t
;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
<M2> UPPER ASS'Y(G)
C1 E
F 605 COVER(TOP/UPP)L COVER(TOP/UPP)R D1 C2 606 604 D2 J H C1 607 B 612 MONI.LOCK ASS'Y
611
MONITOR ASS'Y(G) (Refer to the Exploded view for this part.) 601 616 D1
SUB OPE UNIT
A
610 UPWARDS C2 U.CASE ASS'Y 602
(WR601a) F
617 PASTE
D2
FRAME(UPPER) ASS'Y E SOLDERING 2 POINT 603
G A 614 SCREW * SPEAKER 609 608 BRACKET(SPEAKER) * Mark*: This part was deleted on the way of production.
B
J H
G 613 CONCLUSION SCREW TORQUE TABLE PART.NO 611 ANOTHER SCREW TORQUE 0.2 ±0.01 N�m 0.08 ±0.01 N�m PROCESSING SUB OPE FPC. DRAWING FOR SPACER STICKING. 626 COVER(TOP/UPP)R COVER(TOP/UPP)L 615
VALLEY FOLDING VALLEY FOLDING MOUNTAIN FOLDING
UPPER ASS'Y(G) LYH20626
PROCESSING MONITOR FPC.
PROCESSING SUB OPE.
3 ±1 mm
VALLEY FOLDING AFTER PASTING SUB OPE PUSH TO THIS SLASH PART. MOUNTAIN FOLDING
SPACER(A)
DON'T STICK OUT SPACER IN SUB OPE FPC. VALLEY FOLDING
PASTE SPACERS NOT TO COVER THESE HOLES. STICK TO U.CASE. SHEET STICK ALONG THE REINFORCEMENT BOARD OF FPC. PASTE SPACER INSIDE BKT(UPPER). DON'T RUN A GROUND TO A LEVEL DIFFERENCE OF UPPER CASE. SOLDER 2 POINT MOUNTAIN FOLDING
SPACER(A) SPACER(A)
618 623
SHOULD BE COVERED THIS CONVEX.
SPACER(A) 620
DON'T STICK OUT SPACER IN UPPER CASE. LESS THAN 0.5mm
3 ±1 mm
STICKER
625
624 SPACER(A) 621
SPACER(A)
SHEET STICK ALONG THE CORNER OF FRAME. STICK FPC SO THAT THERE MAY BE NO CREVICE BET MEEN THE HOLE OF IT IN THE RIGHT SIDE OF THE HOLE RING.
PASTE SPACER THIS CONVEX IN UNDER SIDE. DON'T BE SEEN SPACER OUTSIDE OF UPPER CASE.
THE SIDE OF THE HOLE RING IS MET. THESE HOLES CAN BE SSEN.
619
DON'T RUN A GROUND OF UPPER CASE. DON'T SEPARATE.
SPACER(A) SHEET(SHIELD) 622
STICK SPACER THAT FPC MAY BE PRESSED DOWN.
Fig. 1-2-2c UPPER ASS�Y(G)
1-5
|
|
|
> |
|
