|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was having a hard time finding the problem with this Mackie 1604 unit. I didn't have a schematic. Went looking on the web and found your site and the price was more then reasonable. Ordered it and within the hour had the manual and within 15 minutes had the unit fixed. Best $4.99 I ever spent. Thank you.
Doug
;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
<M2> UPPER ASS'Y(G)
C1 E
F 605 COVER(TOP/UPP)L COVER(TOP/UPP)R D1 C2 606 604 D2 J H C1 607 B 612 MONI.LOCK ASS'Y
611
MONITOR ASS'Y(G) (Refer to the Exploded view for this part.) 601 616 D1
SUB OPE UNIT
A
610 UPWARDS C2 U.CASE ASS'Y 602
(WR601a) F
617 PASTE
D2
FRAME(UPPER) ASS'Y E SOLDERING 2 POINT 603
G A 614 SCREW * SPEAKER 609 608 BRACKET(SPEAKER) * Mark*: This part was deleted on the way of production.
B
J H
G 613 CONCLUSION SCREW TORQUE TABLE PART.NO 611 ANOTHER SCREW TORQUE 0.2 ±0.01 N�m 0.08 ±0.01 N�m PROCESSING SUB OPE FPC. DRAWING FOR SPACER STICKING. 626 COVER(TOP/UPP)R COVER(TOP/UPP)L 615
VALLEY FOLDING VALLEY FOLDING MOUNTAIN FOLDING
UPPER ASS'Y(G) LYH20626
PROCESSING MONITOR FPC.
PROCESSING SUB OPE.
3 ±1 mm
VALLEY FOLDING AFTER PASTING SUB OPE PUSH TO THIS SLASH PART. MOUNTAIN FOLDING
SPACER(A)
DON'T STICK OUT SPACER IN SUB OPE FPC. VALLEY FOLDING
PASTE SPACERS NOT TO COVER THESE HOLES. STICK TO U.CASE. SHEET STICK ALONG THE REINFORCEMENT BOARD OF FPC. PASTE SPACER INSIDE BKT(UPPER). DON'T RUN A GROUND TO A LEVEL DIFFERENCE OF UPPER CASE. SOLDER 2 POINT MOUNTAIN FOLDING
SPACER(A) SPACER(A)
618 623
SHOULD BE COVERED THIS CONVEX.
SPACER(A) 620
DON'T STICK OUT SPACER IN UPPER CASE. LESS THAN 0.5mm
3 ±1 mm
STICKER
625
624 SPACER(A) 621
SPACER(A)
SHEET STICK ALONG THE CORNER OF FRAME. STICK FPC SO THAT THERE MAY BE NO CREVICE BET MEEN THE HOLE OF IT IN THE RIGHT SIDE OF THE HOLE RING.
PASTE SPACER THIS CONVEX IN UNDER SIDE. DON'T BE SEEN SPACER OUTSIDE OF UPPER CASE.
THE SIDE OF THE HOLE RING IS MET. THESE HOLES CAN BE SSEN.
619
DON'T RUN A GROUND OF UPPER CASE. DON'T SEPARATE.
SPACER(A) SHEET(SHIELD) 622
STICK SPACER THAT FPC MAY BE PRESSED DOWN.
Fig. 1-2-2c UPPER ASS�Y(G)
1-5
|
|
|
> |
|
