|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
VIDEO RECORDING EN
15
Basic Recording
NOTE:
Before continuing, perform the procedures listed below: � Power ( pg. 11) � Loading A Cassette ( pg. 14) Power Switch Lock Button POWER/CHARGE Lamp Tally Lamp (Lights while recording is in progress.)
Tape Remaining Time
Approximate tape remaining time appears on the display. �� h � � m� means the camcorder is calculating the remaining time. When the remaining time reaches 2 minutes, the indication starts blinking.
� The time required to calculate and display the remaining tape length, and the accuracy of the calculation, may vary according to the type of tape used.
LCD Monitor And Viewfinder
While using the LCD monitor: Make sure the viewfinder is pushed back in. Pull on the bottom end of the LCD monitor to open it. It can rotate 270° (90° downward, 180° upward). While using the viewfinder: Make sure the LCD monitor is closed and locked. Pull out the viewfinder fully.
180�
Power Zoom Lever
Recording Start/Stop Button
VIDEO/MEMORY
1 Remove the lens cap. ( pg. 10) 2 Open the LCD monitor fully. 3 Set the VIDEO/MEMORY Switch to �VIDEO�. 4 Set the Power Switch to �A� or �M� while pressing
down the Lock Button located on the switch.
� The POWER/CHARGE lamp lights and the camcorder enters the Record-Standby mode. �PAUSE� is displayed. � To record in LP (Long Play) mode, pg. 27, 28.
NOTES:
5 To start recording, press the Recording Start/Stop Button. The tally lamp lights and �T REC� appears on the display while recording is in progress. 6 To stop recording, press the Recording Start/Stop Button again. The camcorder re-enters the RecordStandby mode.
Approximate recording time
Tape 30 min. 60 min. 80 min. 30 min. 60 min. 80 min. Recording mode SP 45 min. 90 min. 120 min. LP
� The image will not appear simultaneously on the LCD monitor and the viewfinder except during Interface Shooting. ( pg. 16) When the viewfinder is pulled out while the LCD monitor is opened, you can select which one to use. Set �PRIORITY� to the desired mode in SYSTEM Menu. ( pg. 27, 29) � Colored bright spots may appear all over the LCD monitor or the viewfinder. However, this is not a malfunction. ( pg. 46)
� If the Record-Standby mode continues for 5 minutes, the camcorder�s power shuts off automatically. To turn the camcorder on again, push back and pull out the viewfinder again or close and re-open the LCD monitor. � When a blank portion is left between recorded scenes on the tape, the time code is interrupted and errors may occur when editing the tape. To avoid this, refer to �Recording From The Middle Of A Tape� ( pg. 17). � To turn the tally lamp or beep sounds off, pg. 27, 29.
NOTES:
VIDEO RECORDING & PLAYBACK
 $4.99 GRDX77US JVC
Service Manual Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
|
|
|
> |
|
